An 8 hp pump is installed near the reservoir containing oil having a sp. gr. of 0.82. The rate of flow of the pipe is 0.014 m/s. The pressure heads at 1 and 2 are -28 kPa and 290 kPa respectively. Compute the output in hp by the pump. 290 kPa 50mm o 0.90m -28 kPa 50mm o 8hp pump Oil (0.82)

An 8 hp pump is installed near the reservoir containing oil having a sp. gr. of 0.82. The rate of flow of the pipe is 0.014 m/s. The pressure heads at 1 and 2 are -28 kPa and 290 kPa respectively. Compute the output in hp by the pump. 290 kPa 50mm o 0.90m -28 kPa 50mm o 8hp pump Oil (0.82)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The elevation at point A in the tank below is 32m. Calculate the pressure (in Pa) at the surface of the oil. Use specific wcight of water as 9,81KN/m. 40 m Alr 20 kPa Air Oil 37 m SG -0 85 Water 35 m SG - 2 10
Q2) Calculate The head loss due to friction in The Piping system shown below. The pipe is (150 mm) in diameter and C1som) Long, Passes aflow of Co.13 m/%s 1somm 3om 2.
help with hw...thnks
The 24-in. pipe conducts water from reservoir A to a pressure turbine, which discharges through another 24-in. pipe into tailrace B. The loss of head from A to 1 is 5 times the velocity head in the pipe and the loss of head from 2 to B is 0.2 times the velocity head in the pipe. If the discharge is 25 cfs, (a) What is the head extracted, he, (ft) by the turbine? (b) What horsepower is being given up by the water to the turbine? El 200 ft El 15 ft 24-in. pipe El O ft 24-in pipe
Situation 1 The 60 cm pipe conducts water from reservoir A to a pressure turbine which discharges through another 60 cm pipe into tailrace B. -CL 70 m The head losses are: From A-1 : From 2-B : 0.2 Heo cm g If the discharge is 0.70 m3 /sec: HEL Dn 1. Determine the head extracted by the turbine (HE) in meters. DATUM E 2. Solve for the input power of the turbine (Pinput or Pturbine) in kW. TURBINE 3. At 90% efficiency, compute for the output power (Poutput) for electricity in kW. Situation 2 Pipelines 1,2, and 3 are connected parallel to each other. The three pipes carry a combined discharge of 0.86 m/s. 1 Pipe Length Diameter Friction Factor 1,800 mm 1,500 mm 2,000 mm 0.020 0.018 0.022 400 mm A 2 в у 350 mm 3 300 mm 3 4. Determine the flow rate through pipeline 1 (Q1) in m3/s. 5. Determine the flow rate through pipeline 2 (Q2) in m3/s 6. Determine the flow rate through pipeline 3 (Q3) in m3/s
For the piping system shown below, determine the flow distribution and the piezometric = 20 Kw heads at the junction (j) using the Newton-Raphson Method of solution, power = 0.15 m D,= 0.2 m, D,= 0.15 m, %3D 2. f=0.021, f= 0.018, f,= 0.023 L2=140 30 m B L3=345 L1=95 2 15 m |10 m A Pump 1
Both pistons are moving to the left, but A has a speed twice as great as that of piston B. Then the water level in the tanks is (a) rising (b) not moving up or down, or (c) falling?
shows a pump employed for lifting water from a sump. If its required to pump 60 liters/sec of water through a 0.1 m diameter pipe from the sump to point 10m above, determine the power required. Also determine pressure intensities at L and M. Assume efficiency of 70%. Pu-(YGYLD)
Determine the pressure at point C in psi. Determine the pressure at point D in psi. Determine the flow rate in cfs. Determine the velocity at the pipe with 18 inches diameter in ft/s.
A pump draws water from reservoir A and lifts it to reservoir B as showm, The head los from reservoir A to pipe 1 is 3 times its velocity head and the head loss for pipe 2 to reservoir B is 20 times the velocity head. When the discharge is 20 L/s a) Compute the horsepower output of the pump in kW b) Compute the pressure head at pipe 1 c) Compute the pressure head at pipe 2 EL Om pipe 1 150 mm pipe 2 100 mm -EL-20 m EL 240 m
in a pelton wheel, the bucket peripheral speed is 8m/s, the water jet velocity is 20m/s and volumetric flow rate of the jet is 0.1m^3/s. Is the jet deflection angle is 120 degree and the flow is ideal. Determine the power developed ?
Que.