Water is pumped from reservoir A at elevation 30m through 1200m of 600mm diameter pipe to reservoir B at elevation of 90m. The pump is closed to reservoir A and at the same elevation as A. A hydraulic motor is placed in the pipeline at a midpoint on the length of the pipe and at elevation 80m. The motor delivers 56hp and has an efficiency of 80%. Use f-0.03. If the rate of flow is 850L/s. (WRITE THE NUMERICAL VALUES ONLY WITH 3 DECIMAL PLACES)

Water is pumped from reservoir A at elevation 30m through 1200m of 600mm diameter pipe to reservoir B at elevation of 90m. The pump is closed to reservoir A and at the same elevation as A. A hydraulic motor is placed in the pipeline at a midpoint on the length of the pipe and at elevation 80m. The motor delivers 56hp and has an efficiency of 80%. Use f-0.03. If the rate of flow is 850L/s. (WRITE THE NUMERICAL VALUES ONLY WITH 3 DECIMAL PLACES)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The allowable Net Positive Sustion Head (NPSH) for a pump provided by the manufacturer for a flow of 0.05 m³/s is 3.3 m. The temperature of water is 30° C (vapour pressure head absolute = 0.44 m), atmosphere pressure is 100 kPa absolute and the head loss from the reservoir to pump is 0.3 N-m/N. Find the maximum height of the pump above the sustion reservoir.
simple solution is needed
Note: Don't copy from Chegg.
(b) A water turbine model is constructed at ratio of 1:8 with power system of 10 kW at speed of 555 rpm under a head of 2.5 m. Overall efficiency for both model and prototype is assumed at 0.93. (i) Detemine the specifie speed. mine t); (ii) If the prototype is run under a head of 25 m, calculate its rotational speed, power and discharge.
Non-positive displacement pump is the type of pump whose size is lesser for a given discharge räte. Select one O True O False
3) A centrifugal pump delivers water between two reservoirs with a 300 ft. elevation difference (Az). The 12-in diameter suction pipe (f1= 0.020) is 100 ft. long (L1) and the 10-in diameter discharge pipe (f2= 0.026) is 5000 ft. long (L2). The pump has a performance curve defined by the equation: h, = 375 - Q² where h, is the pump head in feet and Q is the discharge in ft/s. a) Calculate the discharge, Q. b) Calculate the NPSHA. Assume standard atmospheric conditions, 60°F water, and a pump elevation 8 ft. above the lower reservoir Az D, L2 2 D, Ly. ft LOM
The pumping system below is used in a manufacturing process involving glycerin. Find the minimum pump head, E (P), required to prevent contamination of the piping system from reservoir B. the temperature of the glycerin is 60°F. Assume no losses in pipe 2 which connects reservoir B and node A. The check valve only allows flow from reservoir B to node A.
A 30 cm pipe is connected by a reducer to a 10 cm pipe. points 1 and 2 are along the same elevation. the pressure at 1 is 200 Kpa. the flow is 30 litres/s and the energy lost between 1 and 2 is equivalent to 20 Kpa. Compute the pressure at 2 if the liquid flowing is water.
S.speed of the pump.,
5. ol with sp. gr. of 0.88 is being pumped frem a lower reservolr to an elevated tank The pump In the system is 65% efflelent and Is rated at 160kW. Determine the flow rate of the oll in the pipe if the total head los (rom point 1 to point 2 is 5.5m of oll. 150m 200-mm Pump Elev 160m Elev. 150 m
Water at 10°C flows at the rate of 900 L/min from the reservoir and through the copper tube type K . Compute the pressure at point B, just considering the energy loss due to the straight pipe and neglecting the others losses(elbows and tank outlet)