A pump draws 24L/s of water from reservoir A and lifts it to reservoir B. The head lost from A to 1 is 3 times the velocity head in the 150mm suction line and the head lost from 2 to B is 25 times the velocity head in the 100mm discharge line. (A) What is the power delivered by the pump to the system in hp? (B) What is the pressure head in meters in point 1? (C) What is the pressure head in meters in point 2?

A pump draws 24L/s of water from reservoir A and lifts it to reservoir B. The head lost from A to 1 is 3 times the velocity head in the 150mm suction line and the head lost from 2 to B is 25 times the velocity head in the 100mm discharge line. (A) What is the power delivered by the pump to the system in hp? (B) What is the pressure head in meters in point 1? (C) What is the pressure head in meters in point 2?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

6. The nozzle which furnished the water to a certain hydraulic turbine 275 mm in diameter and has coefficient of velocity and discharge of 0.98 and 0.955 respectively. The nozzle is supplied from a 60 cm pipe in which the water approached the nozzle with a total head of 330 m. Compute the energy per second delivered by the jet to the turbine and the energy measure in horsepower lost in passing through the nozzle.
During a flow of 450 L/s, a pressure of 65 kPa was measured at point C in 320 mm diameter horizontal the supply line of water turbine and a -47 kPa pressure T. was measured at point D, 2 m below point C at the 460 diameter exit pipe. mm Compute the total head extracted by a. the turbine. b. Compute the power supplied to the turbine in horsepower.
The nozzle which furnished the water to a certain hydraulic turbine 275mm in diameter and has coefficients of velocity and discharge of 0.98 and 0.96, respectively. The nozzle is supplied from a 60cm pipe in which the water approached the nozzle with a total head of 330m. Compute the following: a. Energy per second delivered by the jet to the turbine. b. Energy measured in hp lost in passing through the nozzle.
Question 4: H₂=4 m f=0.15 D₁ = 50 mm H₁ 4 m 25 m L = 100 m A. Two tanks A and B were connected by a 50 mm-diameter pipe (f=0.15) that is 100 m in length. Calculate the total flow between the two tanks. B. A pipe of 200mm diameter (f-0.01) and length X is to be connected in series to replace X length of the 50mm pipe. If the purpose is to increase flow by 50%. Find Length X. ***** La=X f=0.01 D. = 200 mm
The pump whose characteristics are: H, = 80 – 600V²2 %3D n = -1500V² + 700V Elevation = 230 m |(2) (1) Elevation = 200 m 1000 m pipe 40 cm in diameter Pump Figure Q3 is used to pump water (µ=0.001kg/ms) a distance of 1000 m between two reservoirs the elevations of which are shown in Figure Q3 and remain constant. The pipe is 40 cm diameter commercial steel (ɛ=0.046 mm). Ignoring minor losses and assuming fully turbulent flow. Determine d) The volumetric flow rate e) The efficiency at the operating point
The pump draws oil with specific gravity of 0.90 from a reservoir and delivers it to the hydraulic cylinder. The cylinder has an inside diameter of 5.0 inch and in 15 seconds the piston must travel 20 inches while exerting a force of 11,000 lb. It is estimated that there are energy losses of 11.5 lb-ft/lb in the suction pipe and 35.0 lb-ft/lb in the discharge pipe. Both pipes are 3/8-in Scheulde 80 steel pipe with inside diameter of 0.423 inch. Calculate the pressure at the cylinder.
For the setup shown in the figure :
Determine the flow distribution of water in the system shown in Figure below. Assume constant friction factors, with f= 0.03. The head-discharge for the pump is Hp = 70 m el 50 m Pipe L (m) D (mm) ΣΚ el 48 m 1 100 750 850 350 200 200 [2] [4] 3 el 0m [5] 4 500 200 350 250 [1] [3]
the 9.63. When glycerin (25°C or 77°F) flows through a 30 m (100 ft) length of 75 mm (3 in.) pipe, the head loss is 36 m (120 ft). Calculate the flowrate. 9.64. A pump of what power is required to pump 40 1/min of crude oil from a tank of surface elevation 12 to one of elevation 18 through 450 m of 75 mm pipe, if the oil is at (a) 25°C, (b) 40°C?
The 600 mm pipe shown conducts water from reservoir A to a pressure turbine, which discharges through another 600 mm o pipe into tail race B. The head lost from A to 1 is 5 times the velocity head in the pipe and the head lost from 2 to B is 0.2 times the velocity head in in the pipe. If the discharge is 700 L/s A) Compute for the total head lost 1. 05: Compute for the extracted energy cause by the turbine Compute for the hp given up by the turbine. V Answer A) EL 60m 600 mm 1.63 m 58.37 m 537.3 hp 600 mm o B ▷ EL 0 m
Please solve in detail.
Please correct answer And solve both part