solution and diagrams

Q: Using an engineer's level, the reading on a rod 80 m away was observed to be 2.84 m. The bubble was…

A:

Q: show the integration process

A: To show the integration process

Q: The state of stress at a point is the result of two loadings as shown in figure. When acting alone,…

A: For the two loadings act simultaneouslythen resultant (absolute) shear stress at that point with…

Q: Two pipes of diameters d1 and d2 converge to form a pipe of diameter d. If the liquid flows with a…

A:

Q: 3. Influence lines for trusses. The bridge truss shown in the figure is to be subjected by uniform…

A:

Q: For the beams shown, draw the influence 1ines for the given functions. Use the beam sign convention…

A:

Q: Design the cross section of an isolated T-beam following ACI provisions for a factored moment of…

A: A T-beam (or tee beam) is a load-bearing structure made of reinforced concrete, wood, or metal that…

Q: A W30x90 A36 steel girder spans 12 m on simple supports. It carries a uniformly distributed load of…

A: a. To determine the required section modulus, we need to calculate the maximum bending moment the…

Q: 10 25k 10'

A: The below cantilever beam is given;

Q: Find and define " horton equation" Show illustration.

A: To find and define Horton equation.

Q: Determine the reaction/s at each support, given the data and figure below. X 3 kN/m Y= 14 kN/m L= 3…

A:

Q: mal stress for the steel used i e beam to support the loadim

A:

Q: Determine the yield modulus of elasticity and yield strength of an aluminum material with the…

A: The stress is taken in y-axis and strain in x-axis. From the data, stress-strain curve are being…

Q: A beam has a cross-section as shown. At a section where the shear force is 12 kN, 100 mm a.…

A:

Q: The top of a tower signal at B, 2,000 m from A away was sighted through a transit with recorded…

A:

Q: .) Determine shear and moment equations of the beam shown. Neglect horizontal reactions since ther…

A:

Q: The average normal stresses developed in section a - a of the turnbuckle, and the bolts shanks at B…

A: Given Data Cross sectional area at section a-a = 1in. × 0.25 in. Diameter of bolt shank (d) = 0.5…

Q: A constant force F is applied to the cord to cause block A to move up 3 ft with a speed of 12 ft/s.…

A:

Q: 300 mm PDL = 15 kN/m , PLL = 5 kN/m 2 - 16mm 4m 5m 3m 450 mm fel - 20 Z MPa 4 - 25mm

A: Note:- As per guidelines we are allowed to solve first three supports in case of multiple sub-parts…

Q: 1 Plastic State: For the following section determine the maximum bending moment the section can take…

A: Given: The strength of the concrete is 45 MPa. The strength of the steel is 400 MPa.

Q: Summary of Answer: Suction Hydraulic Head 1 Head 42 Conductivi Difference ty (K) Suction Head Total…

A: Consider the given data z1=0.8=-80 cmz2=1.9=-190 cmz1-z2=-80+190=110 cm Total head, h=ψ+2z=gravity…

Q: A concrete column that is part of a truss is under stress. Determine the maximum tension strength of…

A:

Q: The three-reservoir system is shown below: A A 2 1 3 C The elevation of Reservoir at A is 140m and…

A:

Q: Determine (a) the shear strains at all corners and (b) average normal strain that occurs along…

A:

Q: 17. Referring to Fig. FOS-SP-008, the observed interior angles are: A = 100°45'37", B = 231°23'43",…

A: To compute Corrected interior Angles of the Traverse.

Q: 4. For the system shown in the figure below: Datum 5.0 m 7.0 m 5.0 m a) Flow rate per meter length…

A: Given data in question  Flownet Head difference  Void ratio Specific gravity  To find out  Discharge…

Q: A line has a magnetic bearing of S 41°30' E when the declination was 1°30' E. Find the true bearing…

A: The magnetic bearing is S41°30'E. The declination is 1°30'E. The local attraction is 3°30'E.

Q: The thin-walled vessel shown is fabricated by joining two cylinders with thickness 26 mm using 20…

A: Given, Thickness of the vessel, t= 26mm Number of bolts= 20 Diameter of the bolts= 20mm Outer…

Q: The data of a closed traverse is shown below. Complete the table below and determine the area using…

A:

Q: find the rod reading at P

A: given- a wye level  is used to take reading at point P and Q. to find- rod reading at P.

Q: Please include complete solution and diagram if possible.

A:

Q: Determine the maximum shear stress acting at section a-a of the beam below. 20 mm 4 kN 8 kN 70 mm…

A:

Q: 2. Determine whether each of the trusses below are internally determinate, indeterminate, or…

A:

Q: Problem I. The masses of the frictionless cylinders A and B are 2.0 kg and 1.0 kg, respectively.…

A:

Q: We know the coordinates of points a, b, c, d, e, f and g Compute the area of a polygon made of the…

A:

Q: Your assigned problem: If the water surface elevation in reservoir B is 110m, what must be the water…

A:

Q: A 3" diameter bar is supported by a smooth pin in C and a cable from A to B around the smooth peg at…

A: Given: Diameter of bar = 3'' , Diameter of cable = 0.6'', Wt. of bar = 2500lb/ft3

Q: A composite floor system consists of W18 x 97 beams and a 5-inch-thick reinforced concrete floor…

A: Data Given: Section: W18×97thickness of RCC slab = 5"Span Length = 30 feetSpacing = 8 feetCL = 20…

Q: Alum at a rate of 20 mg/l is added to an incoming discharge of 0.5 m3/s which carries 250 mg/1 of…

A: 1. Alum added at a rate of 20 mg/l.2. Incoming discharge: 0.5 m³/s3. Incoming discharge carries 250…

Q: Four beams, each with a length of 2a, are nailed together at their midpoints to form the support…

A: Vertical analysis Vertical analysis is a sort of financial statement analysis that expresses each…

Q: A vertical curve is to be laid out. The curve is 900.00ft long, g1= -2.5%, g2 = +3.5%, STA@BVC (VPC)…

A: L = Length of curve = 900 ftg1 = Intial grade = - 2.5%g2 = Final grade = 3.5 %BVCSTA = 55 +…

Q: A surveyor forgot to note the distance and bearing of a line while performing a close traverse.…

A: