Q.3) An electrical motor located at A operates at a frequency of 25 Hz and suppliespower to the gear system shown below to run a machine located at F. Thediameters of the shafts are: DAB = 20 mm, DcD = 15 mm and DeF = 30 mm. Theallowable shear stress in the shafts is 60 MPa. Determine the maximum powerthat can be transmitted through this gear system.150 mm150 mm-60 mm60 mm

Answered: Image /qna-images/answer/28012815-ca20-4ddf-a3cf-d514f92d2789.jpg

Answered: allowable shear stress in the shafts is…

allowable shear stress in the shafts is 60 MPa. Determine the maximum power that can be transmitted through this gear system.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A…

Q: Two parallel shaft connected by spur gears turn in the same direction and having a speed ratio of SR…

Q: The steel shaft with two different diameters rotates at 4.5 Hz. The power supplied to gear C is 51.7…

Q: Determine the minimum shaft diameter at locations A, B, C, D, & E for an enclosed industrial…

Q: A single stage spur gear gearbox has a module of 1.5mm and an input speed of 1500.p.m. and a pinion…

A: For the given yield stress and materials,Consider the velocity factor and service factor to be, .

Q: A gear train is composed of four helical gears with the three shaft axes in a single plane, as shown…

Q: 100 T 40 T The spur gear set shown has 20° pressure angle with a module of 6 mm. The unit transmits…

A: Given data: The the number of teeth on gear 1 is T1=40 The pressure angle for spur gear is ϕ=20° The…

Q: In the gear system of Figure 4, a torque of 5 N-m is applied on gear E. Shaft (1) and shaft (2) are…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A motor transmits 40 hp to an air conditioning apparatus by means of a roller chain. The motor runs…

A: If you have any doubts feel free to ask.... Thankyou

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

Q: the diameter of solld snaft (2) IS E. 72 teeth 30 teeth (1) (2)

A: Givenspeed of motor NA=808rpmZA=24ZB=72ZC=30ZD=60

Q: A motor supplies 173 hp at 650 rpm to flange A of the shaft. Gear B transfers 75 hp of power to…

Q: Calculate the shaft diameter necessary to support a combined maximum bending moment of 2000 Nm, and…

Q: Grocery checkout conveyor N, =72 teeth Electric motor @, = 1200 rpm N1 = 18 teeth

A: In the given problem initially the set of gears applied to this system of an electric motor to a…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

Q.3) An electrical motor located at A operates at a frequency of 25 Hz and supplies
power to the gear system shown below to run a machine located at F. The
diameters of the shafts are: DAB = 20 mm, DcD = 15 mm and DeF = 30 mm. The
allowable shear stress in the shafts is 60 MPa. Determine the maximum power
that can be transmitted through this gear system.
150 mm
150 mm
-60 mm
60 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A gearbox is to be designed with a compound reverted gear train that transmits 25 horsepower with an input speed of 1000 rev/min. The output should deliver the power at a rotational speed in the range of 280 to 300 rev/min. Spur gears with 20° pressure angle are to be used. Determine suitable numbers of teeth for each gear, to minimize the gearbox size while providing an output speed within the specified range. Be sure to avoid an interference problem in the teeth. The suitable numbers of teeth for each gear to minimize the gearbox size while providing an output speed within the specified range are N2= N3= N4= N5= teeth teeth teeth teeth
A motor supplies 173 hp at 650 rpm to flange A of the shaft. Gear B transfers 75 hp of power to operating machinery in the factory, and the remaining power in the shaft is transferred by gear D. Shafts (1) and (2) are solid aluminum [G = 4400 ksi] shafts that have the same diameter and an allowable shear stress of T = 5.8 ksi. Shaft (3) is a solid steel [G=9100 ksi] shaft with an allowable shear stress of T = 10.2 ksi. Assume that L₁=2.3 ft, L₂=1.2 ft, L3-2.9 ft. Determine: (a) the minimum permissible diameter d₁=d₂ for aluminum shafts (1) and (2). (b) the minimum permissible diameter d3 for steel shaft (3). (c) the rotation angle D/A of gear D with respect to flange A if the shafts have the minimum permissible diameters as determined in (a) and (b). Answers: (a) d₁=d₂ = i (b) d3= i (c) & DIA = i (1) L₁ TB. B (2) L2 in. in. o' (3) L3 Tp Mommu D
In a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast iron profile. The diametral pitch is 6-teeth/in, the face width si 0.5 inches, and the pressure angle is 20 degrees. Assume that the pinion transmits 10 hp at a speed of 2000 rpm. Find the pitch diameters of the gears. Find the pitch line velocity in ft/min Find the velocity factor Ky Find the tangential load in lbf Find the contact stress in kpsi, assuming CP=1960 psi.
Spur gear train is used to transmit the power of 2kW from input gear A rotating at 120 rpm to output gear D through a compound gear BC. The number of teeth on the gear A, B, C and D are 16, 32, 12 and 18 respectively. Given: Module = 4mm, pressure angle=20° The tangential force acting on the gear B is N A D В
The gear ratio shown must transmit 10 horsepower (66000 lb in/s) from its input, which is rotating at a speed of 1200 revolutions per minute. It must increase the torque received at its input shaft 16 times. Spur gears with 20° pressure angle should be used. Input and output shafts should be aligned. The transmission should take up as little space as possible. The distance between the centers of the input shaft and the intermediate shaft (the one that loads gears 3 and 4) should be 10 inches. Determine the magnitude of the radial load that gear 4 exerts on gear 4. Write your answer in pounds.
Please answer in proper units
HW12 The gearing of a machine tool is shown in the Figure below. The motor shaft is connected to gear A and rotates at 1500 r.p.m. The gear wheels B, C, D and E are fixed to parallel shafts rotating together. The final gear F is fixed on the output shaft. Fined: 1-the speed of gear F 2- rotating speed of gears (B, C, D and E) The number of teeth on each gear are as given below: Gear A B C D E F No. of teeth 25 35 90 30 80 60 + A B E+ D F LL
Torque in = 40nm Holding torque out = 896nm 8.Using your answers from the gear box above, and given that the input shaft has a diameter of 12 mm and the output shaft has a diameter of 15 mm, both shafts are made from aluminium. When this transmission system was operated, it failed. Identify the position where the failure occurred and the reason for this failure. Suggests improvements to the system to overcome the failure mode. The shear strength of aluminium is 207 MPa.
A shaft drives a gear set that is transmitting 8 hp at 2250 rpm. The diameter of the shaft is 1.75 in. Determine the torsional shear stress developed in the shaft.