A gearbox is to be designed with a compound reverted gear train that transmits 25 horsepower with an input speed of 1000 rev/m The output should deliver the power at a rotational speed in the range of 280 to 300 rev/min. Spur gears with 20° pressure angle to be used. Determine suitable numbers of teeth for each gear, to minimize the gearbox size while providing an output speed with the specified range. Be sure to avoid an interference problem in the teeth. The suitable numbers of teeth for each gear to minimize the gearbox size while providing an output speed within the specified rar are N2 = N3 = N4= N5= teeth teeth teeth teeth

Q: interference, determine the number of teeth and stages to produce a speed reduction of 42:1. Sketch…

A:

Q: A gearbox is needed to provide an exact increase in speed, while minimizing the overall gearbox…

A: Given:Achieve an exact output speed of 13250 rpm while minimizing gearbox size and transmitting 18…

Q: Design a two-stage compound spur gear train for an overall ratio of approximately17+01:1. Specify…

A: overall ratio=17+11=181

Q: Examine the gear drive shown.  The small driving gear has 15 teeth, DP = 8, RPM = 1200, Torque = 4…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: The shaft rotating at 550 rpm carries a spur gear B having 96 teeth with a diametral pitch of 6 and…

A: Given data as per the question Speed of shaft =550 rpm No. of teeth on gear B =96 Diametral pitch =6…

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A:

Q: A gear box has an input speed of 2,000.00 rev/min clockwise and an output speed of 500.00 rev/min…

A: Given data, Nin = Input speed = 2000 rev/min Nout = Output speed = 500 rev/min Pin = Input power =…

Q: What is the transmitted load exerted by the pinion on the gear? Report your answer in lbf.

A: Given:Pinion Np=17 teeth, Gear Ng=52 teeth, Pressure angle∅=20∘ Power H=4 hp Diametral pitch Pd=10…

Q: A pair of iron cast gears connecting two shafts at the Angle of the elbow. The diameter of the…

A: pitch diaDG=100mm=0.1mDP=80mm=0.08mϕ=14.5°σOP=55MPaσOG=55MPaP=2.75kWεP=εG=84kN/mm2

Q: A 17-tooth 20° pressure angle spur gear rotates at 1800 rev/min and transmits 4 hp to a 52-tooth…

A:

Q: A gearbox is needed to provide an exact increase in speed, while minimizing the overall gearbox…

A: Given:The power required to transmit gearbox is .The output speed is .The input speed is .Formula…

Q: What is the total force exerted by the pinion on the gear? Report your answer in lbf.

A:

Q: For the gear train shown below determine the velocity ratio, output speed, output direction, output…

A: Given:  No. of Teeth in Gear A, ZA = 20 Rotational Speed of Gear A, NA = 3000 rpm  (CW) Input Torque…

Q: Grocery checkout conveyor N, =72 teeth Electric motor @, = 1200 rpm N1 = 18 teeth

A: In the given problem initially the set of gears applied to this system of an electric motor to a…

Q: The number of teeth on pinion

A: Given; Determine the number of teeth on pinion ?Where,  A pair of spur gears with;Module, m=5…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.