After the locomotive has travelled 5.83 km, the engine comes back online. What is the torque required to maintain that constant speed? Assume that work is provided from the engine to the wheels via a single shaft, which has a constant rotational speed of 230 rpm, and that the mass of the locomotive is 193 tonnes. Give your answer in kNm.

After the locomotive has travelled 5.83 km, the engine comes back online. What is the torque required to maintain that constant speed? Assume that work is provided from the engine to the wheels via a single shaft, which has a constant rotational speed of 230 rpm, and that the mass of the locomotive is 193 tonnes. Give your answer in kNm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Now consider two very similar semi trucks. One travels at 40 km/hr and another travels at 75km/hr. Which truck will have the greater motion inertia?
i need the answer quickly
A gearset has a module of 5 mm, a 20 degree pressure angle, and a 24-tooth cast iron spur pinion driving a 48-tooth cast-iron gear. The pinion is to rotate at 500 rev/min. The objective is to calculate the power in kwatt that can be transmitted by the gearset.. In this case, the cast iron, cast profile gears and the velocity factor must be calculated from the Barth equation. The bending stress is limited to 50 MPa and the facewidth is 60 mm. The velocity factor is considered to be significant and must be used in stress calculations. Calculate the power in kwatt the gearset can transmit using the Lewis bending equation. Note: in this case the stress MUST be modified by the velocity factor, Kv.
A cart is moving in a track which is shown in the bellow picture(both friction and rotation is not acting on this cart) v = 0 50 m 50 m 40 m 20 m (1)Draw an energy diagram as the cart moves on the track (kinetic energy, potential energy, and the total energy lines are required) (2)Label the points where the cart is in stable equilibrium, unstable equilibrium, and any turning points (3)Find the Maximum and Minimum speed.
i need the answer quickly
When in the mode of adsorbing, the vertical shaft is rotating with an angular velocity of 3 rad/s at 0 = 0°. When picking up trashes, a force F needs to be applied to the collar so that 0 = 90°. Help students determine the angular velocity of the shaft at 0 = 90°. Also, find the work done by force F from 0 = 0° to 0 = 90°. Neglect the mass of rods GH and EF and the collars I and J. The rods AB and CD each have a mass of 10 kg. 0.3 m E 0.3 m 0.1 m 0.3 m A 0.1 m H F 0 0.3 m B
You have your bicycle upside down while you adjust the chain. The chain is wound around the rear wheels small gear, which has a radius of 4.0 cm. At the pedals, the chain is wound around the large gear, which has a radius of 11.0 cm. The radius of the rear wheel is 35.0 cm. You spin the pedals initially so they finish two revolutions in 1.0 s, starting from rest. Assume constant acceleration. (a) Find the angular acceleration of the rear wheel in rad/s2. (b) Find the magnitude of the total acceleration of a point at the edge of the small gear at the end of 1.5 s (the sum of the radial and tangential accelerations). (c) What is the tangential acceleration for that point during the first second? (d) Calculate the linear acceleration of the chain.
Do neat work
The variation diagram of the cutting force of the cutting work done with the press shown in the figure is given in the figure. Engine speed is 1400 rpm, flywheel speed is 75 rpm. The moment of inertia of the rotating masses in the engine is 0.75 kgm^2. Calculate the flywheel moment of inertia required for the press so that the velocity unevenness is 0.02. It is known that the engine power is 2 kW.
In the geared shaft shown below, gears A and B and gears C and D are separated by 500 mm. Gears B and C are separated by 400 mm. Gear A is experiencing a 250N⋅m250N⋅m clockwise torque; gear B is experiencing a 75N⋅m75N⋅m counter-clockwise torque; gear C is experiencing a 325N⋅m325N⋅m counter-clockwise torque; and gear D is experiencing a 150N⋅m150N⋅m clockwise torque. What is the absolute maximum shear stress in the shaft (in MPa) if the shaft has a 50-mm diameter?
solve part (iv)
Solve the problem correctly,Will upvote