A power transmission system consists of a motor connected to a pulley and a belt. The motor has a power output of 10 kW and operates at a speed of 1200 rpm. The pulley connected to the motor has a diameter of 300 mm, while the pulley connected to the driven shaft has a diameter of 600 mm. The belt used has a coefficient of friction of 0.3. Determine the maximum torque that can be transmitted by the system and the rotational speed of the driven shaft.

Q: the efficiency of gear train

A: Given data; The efficiency of reducer gear train=1 kWSpeed,N=1444rpmTorque=56.36 NmRatio of speed…

Q: Compute the torque in N∙m developed by an industrial motor whose output is 150 hp at an angular…

A: Given:P=150 hpN=400 rpm

Q: r-stroke engine (c) be the same as that of the four-

A: GIVEN:A two-stroke engine has a speed of 750 rpmA four-stroke engine has a speed of 1500 rpm

Q: A slider crank mechanism operates at 5 m/s and applies a force of 40 N to the slider. The slider…

A: Given:- Force= 40N Velocity of slider= 5 m/s Slider weight= 3 kg Slider Dimension:= 0.6 x 0.2m

Q: Find the power transmitted by a belt running over a pulley of 500mm diameter at 300 rpm.The…

A:

Q: 100 T 40 T The spur gear set shown has 20° pressure angle with a module of 6 mm. The unit transmits…

A: Given data: The the number of teeth on gear 1 is T1=40 The pressure angle for spur gear is ϕ=20° The…

Q: A polyamide F-0 flat belt 80mm wide is used to transmit 5 kW under light shock conditions where Ks =…

A:

Q: (d) The schematic arrangement of a braking system is shown in figure below. The load weighs 50 kN…

A: Given data Diameter of the hoist drum Dh= 500mm = 0.5m Diameter of the brake drum / wheel Dw =…

Q: Question Two: The initial tension in a belt drive is found to be 600 N and the ratio of fri tension…

A: To Find : The velocity of belt for maximum power transmission Given : The initial tension is The…

Q: A four-stroke, 12-cylinder diesel engine has a bore and stroke of 820 mm and 2020 mm, respectively,…

A:

Q: The tension in a pulley belt is 300 N when stationary. The smaller pulley has a diameter of 300 mm…

A:

Q: Two machines are coupled by means of a clutch plate with 2 contact surfaces. The plate has an inner…

A: GIVEN WE have,contact surface clutch plate inner diameter (d1 )=130mm=0.13mtrouter diameter (d2…

Q: To design a gearbox that will allow a motor to lift a 120lbf load 60ft vertically in 30 seconds…

A: A transmission is another name for a gear box. A set of gears and their case, most typically…

Q: In the rigid rotor and elastic rotor models, indicate the differences between the expressions…

A: Given:In the rigid rotor and elastic rotor models, indicate the differences between the expressions…

Q: B A, UBC Engineering Your team is prototyping a simple braking system for your model car. The 2.2 kg…

A: GIVEN:mass of wheel, m=2.2kgradius of wheel, r=0.25mangular velocity,…

Q: The electric motor shown below has a power rating of 18 hp and operates at 3080 RPM. It powers a…

A:

Q: pulleys are 300 and 850 mm, respectively, and the center distance is 2 m. The belt has a width of…

A: As per given question We have to determine a. The contact angles and belt length for an open…

Q: A multi-plate friction clutch has to be designed to transmit 100 kW from an internal combustion…

A:

Q: A short-shoe drum brake having f= 0.25, a = 1.0 m, b = 0.4 m, c = 50 mm, and r= 0.3 m is to absorb…

A:

Q: 6 – The brake power of a single cylinder engine is defined by the relation BP = 9.75 (N/1000)3 Where…

A:

Q: Two types of motorcycle, Type A has two identical and independent tires, and the failure rate of…

A: failure rate of tyre A,PA=0.0006/hrnA=2 tyresfailure rate of tyre B,PB=0.0006/hrnB=3 tyresa) Failure…

Q: A conical clutch has an included angle of 105°. The outer and inner diameters are 110 mm and 40 mm,…

A: Consider 'W' be the axial load on the clutch, R and r be the outer and inner radii of the clutch…

Q: For a radial bearing the desired rated life is 10000 hours for a speed of 600 rpm and radial load of…

A: As given in the question, Desired rated life in hours = Lh = 10000 hr Rotational speed = N = 600 rpm…

Q: The machine design has stated that a 2.5 kW electric motor with an input speed of 1000 RPM is needed…

A: Given Data The power of the electric motor is: P=2.5 kW The input speed is: N=1000 RPM Th overall…

Q: Jestion 3 A flat belt drive connects two pulleys 5 meters apart: The 2m pulley diameter driver…

A: Given, Distance between the two pulleys, L=5mDriver diameter, D1=2mN1=350rpmDriven diameter,…

Q: shown below. The coefficient of friction for the screw is f = 0.06 and friction du negligible f≈ 0.…

A:

Q: . Find the horsepower transmitted by a pair of friction wheels, the diameter of driving wheel is 10…

A: Given:Diameter of the driving wheel, d=10 inSpeed of the wheel, N=200 rpmWidth of the wheel, w=2…

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.