press tool machine uses a flywheel in the form of a solid steel disc 0.7 m diameter and 0.1 m thick rotating with a mean speed of 60 rev/min. The density of the steel is 7830 kg/m^3. The press is operated once every 5 revolutions and a torque of 2000 Nm is exerted on the tool for a duration of 0.05 seconds. determine the following: The energy absorbed is replaced during the rest of the cycle. The coefficient of fluctuation of speed .The maximum and minimum speeds of the flywheel

Q: Design a single-plate automobile clutch to transmit a maximum torque of 250 N-m at 2000 rpm. The…

A:

Q: B) A petrol engine of compression ratio 6 uses a fuel of calorific value 43950kJ/kg. The air - fuel…

A: Given data as per questionCalorific value of fuel =43950 kj/kgFuel ratio =15:1Compression index…

Q: Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are…

A: The objective of the question is to find the length of the belt required, the angle of contact…

Q: A shaft is fixed at support C and has a torque of 75lb.ft  with respect to free end at a distance of…

A: givenM1=75lbft  at 0.75ft  from fixed end CW2=1200lb/ft M2=600lbft at free end

Q: Problem Statement: One cable runs from a winch motor M, around pulley D, to the ceiling. A and C.…

A:

Q: À three-bladed wind turbine has a small, unbalanced mass m =0.3 kg, located at an eccentricity…

A: Given

Q: The turning-moment diagram for one cycle of a multi-cylinder engine shows fluctuations in energy…

A:

Q: When in operation, the shaft shown experiences a fully reversible torque. It is machined from a 1040…

A: Given: The factor of safety, N = 2 The type of material = 1040 Hr steel The number of cycle, n =…

Q: A pulley is keyed to a shaft midway between two anti-fiction bearings. The bending moment at the…

A:

Q: The mechanism of a wrapping machine, as shown in Figure, has the following dimensions : ОА 3 100…

A:

Q: The turning moment diagram for a petrol engine is drawn to the following scales: turning moment 1 mm…

A: The fluctuation of energy corresponds to 600 mm2. The density of the flywheel is 7200 kg/m3. The…

Q: A torque of 10kN-m is to be carried by a flanged bolt coupling that consists of eight 10mm diameter…

A:

Q: Q4. A worker manually lifts trays of clean dishes of a 20-lbs from a conveyor at the end of a…

A: We can analyze that , At the origin of the lift, the horizontal distance (H) 20 inches, the vertical…

Q: A flat belt is required to transmit 35 kw from a pulley of 1.5 m effective diameter running at 300…

A: Given:P=35 KWd=1.5 mN=300 rpmθ=1124*2πμ=0.3t=10 mm

Q: As shown, a shaft is composed of five cylindrical sections. A motor is attached at F and supplies…

A:

Q: A six-pound weight hanging from the end of a spring is pulled 10 centimeters below its resting…

A: Given that, Weight of hanging block, W=6 lbs,Mass of the hanging block, m=6×0.453592 kg=2.72…

Q: A hydraulic cylinder is used to lift a load of 750 lbf a distance of 4 ft in 3 seconds. Compute the…

A:

Q: 2. Some of the first power-generating wind turbines were small, having blades with a radius of 8.00…

A: Given data: -  The blade radius of the small wind turbine is r = 8.00 m. The large radius of the…

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.