In Figure, the system is filled to height h with a liquid of density p. The atmospheric pressure is Patm Neglecting fluid friction, evaluate the pressure of the fluid at each of the points labeled 1,2, 4, and 5.Compare the pressure at point 3 with that at point 5. Problem 4:PatmThe figure represents a liquid reservoir with anoutflow pipe. The system is filled to height h with aliquid of density p. The atmospheric pressure is Patm-Neglecting fluid friction, evaluate the pressure ofhthe fluid at each of the points labeled 1, 2, 4, and 5.Compare the pressure at point 3 with that at pointPatm5.Solution: P:= Patm +pgh; P2= P4= Ps= Patm; P3= Patm-3pgh

Patm is the atospheric pressure which is present at the top of any liquid surface.the pressure at…

Answered: Problem 4: Patm The figure represents a…

Similar questions

z> Find the difference in pressure (P.-P) for the below pipe System : 20n
What pressure (in N/m2) is exerted on the bottom of a gas tank that is 0.481 m wide by 0.814 m long and can hold 49.7 kg of gasoline when full? (Give only the pressure exerted by the gasoline.) | N/m²
(a) Calculate the absolute pressure at the bottom of a fresh-water lake at a depth of 33.0 m. Assume the density of the water is 1.00 x 103 kg/m3 and the air above is at a pressure of 101.3 kPa. Pa (b) What force is exerted by the water on the window of an underwater vehicle at this depth if the window is circular and has a diameter of 29.0 cm? N Need Help? Read It
The greatest ocean depths on the Earth are found in the Marianas Trench near the Philippines, where the depth of the bottom of the trench is about 11.0 km. Calculate the pressure due to the ocean at a depth of 10.5 km, assuming sea water density is constant all the way down. (The validity of the assumption of constant density is examined in one of the integrated concept problems.) atm
IP The weight of your 1450 kg car is supported equally by its four tires, each inflated to a gauge pressure of 35.0 lb/in^2. what is the area of contact each tire makes with the road? If the gauge pressure is increased, does the area of contact increase, decrease, or stay the same? what guage pressure is required to give and area of contact of 106 cm for each tire? this is one question.
Water towers store water above the height of most consumers for times of heavy use, eliminating the need for high-speed pumps. In this problem use ρ for the density of water and g for the gravitational acceleration. Part (a) What is the height, h, in terms of the variables given in the introduction, that the water level in such a tower must have above a user in order for the user to receive water at gauge pressure P? Part (b) What is this height, in meters, if the gauge pressure required is 2.95 × 105 Pa?
B. An ideal incompressible fluid flows at 0.4 m/s throug a square pipe with a side of 7.0 cm. The pipe narrowst a cylindrical pipe with a radius of 30 mm. assume steac flow throughout the system. What is the speed of fluid through the narrow section of the pipe?
AST Water is flowing in the pipe shown in the figure below, with the 8.20-cm diameter at point 1 tapering to 3.85 cm at point 2, located y 12.5 cm below point 1. The water pressure at point 1 is 3.20 x 10 Pa and decreases by 50% at point 2. Assume steady, ideal flow. What is the speed of the water at the following points? (a) point 1 x Your response is within 10% of the correct value. This may be due to roundoff error, or you could have a mistake in your calculation Carry out all intermediate results to at least four-digit accuracy to minimize roundoff error. m/s (b) point 2 x Your response is within 10% of the correct value. This may be due to roundoff error, or you could have a mistake in your calculation. Carry out all intermediate results to at least four-digit accuracy to minimize roundoff error. m/s
SITUATION. A cylindrical tank 8m in height is lying in horizontal position with diameter of 3m. Oil is flowing inside the tank at a rate of 0.8 ML/min. How fast is the rate of fluid rising when the height is 1 m? (cont) What is the work done in pumping that amount of fluid at a height 1 m above the top of the tank?
The pressure drop along a length of artery is 104 Pa, the radius is 8.5 mm, and the flow is laminar. The average speed of the blood is 12.5 mm/s. P = 104 Par = 8.5 mms = 12.5 mm/s What is the net force on the blood in this section of artery in N? netF? What is thepower experted maintaining the flow in mW?
Question 1 a) Consider the forces acting on an infinitesimal fluid element located at radius r inside a star, where the star is in hydrostatic equilibrium. Show that the buoyancy force acting on the fluid element may be written as Pe dv dt = -(Pe - p)g where Pe is the density inside the fluid element, p is the density of the gas in the surrounding gas at radius r, v is the velocity of the fluid element and g is local acceleration due to gravity. For full marks you should explain each step of your derivation. b) With the aid of a diagram, explain the condition required for convection to occur by considering the small displacement of a fluid element from its original equilibrium location within a star.
Please asap

SEE MORE QUESTIONS