A siphon is used to drain water from a tank as illustrated below. Assume steady flow without friction.h(a) If h = 1.51 m, find the speed of outflow at the end of the siphon.m/s(b) What is the limitation on the height of the top of the siphon above the end of the siphon? Note: For the flow of liquid to be continuous, its pressure must not drop below its vapor pressure. Assume the water is at 11°C, atwhich the vapor pressure is 1.3 kPa.m

Take the reference level as the level of water in the tank. Let Pl be the pressure at height h (the…

Answered: A siphon is used to drain water from a…

Similar questions

16.
A water tank of constant depth H, open to the atmosphere, is connected to the piping system, as shown in Figure P8.45. After a length of pipe L of diameter D, the diameter decreases smoothly to a value of D/2 and then continues on for another length L before exiting to atmosphere. The flow is turbulent and the friction factor f is the same for all piping. CD1 and CD2 are the loss coefficients for the entry and exit. Calculate the depth of the tank required to produce a mean exit velocity of V .
The pressure drop along a length of artery is 103 Pa, the radius is 9.5 mm, and the flow is laminar. The average speed of the blood is 16.5 mm/s.Randomized Variables P = 103 Par = 9.5 mms = 16.5 mm/s a. What is the net force on the blood in this section of artery in N? b. What is the power expended maintaining the flow in mW?
A sump pump (used to drain water from the basement of houses built below the water table) is draining a flooded basement at the rate of 0.550 L/s, with an output pressure of 3.50 x 105 N/m2. You may neglect frictional losses in both parts of this problem. (a) The water enters a hose with a 3.00 cm inside diameter and rises 3.40 m above the pump. What is its pressure (in N/m2) at this point? 383000 X N/m2 (b) The hose goes over the foundation wall, losing 2.00 m in height, and widens to 4.00 cm diameter. What is the pressure now (in N/m2)? 369000 X N/m2
A PROBLEMS 6.63, 6.64 6.64 This "double" nozzle discharges water (at 10°C) into the atmosphere at a rate of 0.50 m /s. If the nozzle is lying in a horizontal plane, what x-component of force acting through the flange bolts is required to hold the nozzle in place? Note: As- sume irrotational flow, and assume the water speed in each jet to be the same. Jet A is 10 cm in diameter, jet B is 12 cm in diame- ter, and the pipe is 30 cm in diameter.
For a given cylindrical tank, the radius is 8 m and the height is 18 m. The tank is filled to a depth of 10 m. How much work is required to pump all of the water over the top edge of the tank? Acceleration due to gravity is 9.8 m/sec and the density of water is 1000 kg/m". Round your answer to the nearest kilojoule. Provide your answer below: W kJ
Note: FBD is mandatory,So please include it.
A tank in the shape of an inverted cone has a height of 20 meters and a base radius of 11 meters and is filled with liquid to a depth of 16 meters. Determine the amount of work needed to pump all of the liquid to a point 1m from to the top of the tank. Assume that the density of the liquid is 793 kg/m 3
A cylinderis fitted with a piston beneath which is a spring, as in the attachment. The cylinder is open to the air at the top. The sprink constant is 4300 N/m. The piston has negligible mass and a radius of 0.032. When the air beneath the piston is completely pumped out, how much does the atmospheric pressure cause the spring to compress? How much work does the atmospheric pressure do in compressing the spring.
The plug has a diameter of 30 mm and fits within a rigid sleeve having an inner diameter of 32 mm. Both the plug and the sleeve are 50 mm long. The plug is made from a material for which E= 1 MPa, v=0.7. (Figure 1) Figure Part A Determine the axial pressure p that must be applied to the top of the plug to cause it to contact the sides of the sleeve. Express your answer to three significant figures and include appropriate units. HA P= Submit Part B Value 8 = Request Answer Also, how far must the plug be compressed downward in order to do this? Express your answer to three significant figures and include appropriate units. μÅ 3 Value Submit Provide Feedback Units Request Answer IWIC ? Units www. ?
A sump pump (used to drain water from the basement of houses built below the water table) is draining a flooded basement at the rate of 0.700 L/s, with an output pressure of 2.00 x 105 N/m². You may neglect frictional losses in both parts of this problem. (a) The water enters a hose with a 3.00 cm inside diameter and rises 3.00 m above the pump. What is its pressure (in N/m²) at this point? N/m² (b) The hose goes over the foundation wall, losing 1.70 m in height, and widens to 4.00 cm diameter. What is the pressure now (in N/m²)? N/m²
A popular pool toy allows the user to push a plunger to compress water in a barrel with a diameter of 3.5 cm. The water is compressed with a speed of 1.9 m/s and emerges from a small opening with a speed of 12 m/s. What is the diameter (in mm) of the opening? Assume the toy is oriented horizontally. mm

SEE MORE QUESTIONS