The plug has a diameter of 30 mm and fits within a rigid sleeve having an innerdiameter of 32 mm. Both the plug and the sleeve are 50 mm long. The plug is madefrom a material for which E= 1 MPa, v=0.7. (Figure 1)Figure< 1 of 1 >Part ADetermine the axial pressure p that must be applied to the top of the plug to cause it to contact the sides of the sleeve.Express your answer to three significant figures and include appropriate units.HAP=SubmitPart BValue8 =Request AnswerAlso, how far must the plug be compressed downward in order to do this?Express your answer to three significant figures and include appropriate units.μÅ 3ValueSubmitProvide FeedbackUnitsRequest AnswerIWIC ?Unitswww. ?

Answered: Image /qna-images/answer/d9ec57f8-560c-42b1-959d-920c7c31971e.jpg

Answered: The plug has a diameter of 30 mm and…

Similar questions

A very deep point of the Pacific Ocean is at a depth of 10,100 m below the surface. What is the gauge pressure in the water at that point? The density of seawater is 1025 kg/m3. Ignore the slight variations of g and ρ with depth. Assume g = 9.80m/s2. Assume 3 significant digits. A. 8.88 ×107 Pa B. 2.22 ×108 Pa C. 1.11 ×108 Pa D. 1.01 x108 Pa E. 3.33 ×108 Pa F. 5.55 ×107 Pa
Pressure cookers have been around for more than 300 years, although their use has strongly declined in recent years (early models had a nasty habit of exploding). How much force (in N) must the latches holding the lid onto a pressure cooker be able to withstand if the circular lid is 21.0 cm in diameter and the gauge pressure inside is 2.60 atm? Neglect the weight of the lid. N
A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 150.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 2.80 MN. W 0 -pressure vessel cm bolts port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm. zide TO 0.P d 220
12 of 20 Provide Feedback P Pearson MacBook Pro
What is the gauge pressure at point A. Write the answer using 2 significant figures (very important)
A pipe with a radius of 51 cm has water flowing at 5.3 m/s. If water goes into a new pipe with radius 21 cm, how much will the pressure decrease? ΔΡ- unit Pa
The figure below shows 5 containers of water. A and B have the same height, as do C and E. A and E have the same area on the bottom, as do B and C. D has the largest area and the lowest height. Rank the pressure at the bottom of each container, from least to most (least occurs first, most occurs last). AVİLI O D, A=B, C=E O C=B, A=E, D OD, С, В, А, Е ОС, В, А, Е, D O D, A-B, C, Е
Find the absolute pressure of a tank whose gauge pressure reads 362 psi. Explain your answer.
please help
Gg
The intake in the figure has cross-sectional area of 0.79 m² and water flow at 0.48 m/s. At the outlet, distance D = 180 m below the intake, the cross-sectional area is smaller than at the intake and the water flows out at 9.1 m/s. What is the pressure difference between inlet and outlet? MPa Reservoir Generator building Intake Outlet→
The four tires of an automobile are inflated to a gauge pressure of 2.0 105 Pa. Each tire has an area of 0.025 m2 in contact with the ground. Determine the weight of the automobile. N