adeslqu Svb (mo) 2. A paper chromatography experiment with metal ions gave the following Rf values: Ni²+ 0.34, Fe3+ =0.45, Cr=0.27, Cu+ =0.15. An unknown was run under similar conditions and the sample moved 2.8 cm with a solvent front of 10.4 cm. Determine the unknown metal ion. Show calculations. %3D slqmsa et 20

adeslqu Svb (mo) 2. A paper chromatography experiment with metal ions gave the following Rf values: Ni²+ 0.34, Fe3+ =0.45, Cr=0.27, Cu+ =0.15. An unknown was run under similar conditions and the sample moved 2.8 cm with a solvent front of 10.4 cm. Determine the unknown metal ion. Show calculations. %3D slqmsa et 20

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Select wether the following statements are True or False: Two compounds that are separated on a 10 cm column have a resolution equal to 1.5. If all conditions remain identical, if the length of the column is doubled, the resolution will increase. An example of a stationary phase support used in strong anion exchange would be a quarternary ammonium-functionalized polymer. In normal phase chromatography, a more polar compound will have a higher partition coefficient than a compound that is less polar. In gas chromatography, compound with higher boiling points generally (but not necessarily) elute later than compounds with lower boiling points. In a chromatographic separation, a compound with a capacity factor equal to 1 must spend an equal amount of time in the mobile phase as it does in the stationary phase.
In the table below, record the color that you observe for each spot or component of each spot after the run is completed. For the retention factor, R₁, write in the numerator (top) the number of mm that the spot has moved and in the denominator (bottom) the number of mm that the solvent has moved from the point where the samples were 'spotted. Calculate the Rf vale for each spot or component of each spot. Im having a difficult time finding the Retention Factor for M&Ms by using Salt water and seeing how much each color moves Instructions Coffee filters usually are round, but it's easier to compare your results if the paper is rectangular. So, your first task is to cut the coffee filter into a rectangle. Measure and cut a 2-3/4" by 7" strip from the middle of a coffee filter. This is easily done by folding the filter in half (to make a half-circle) and then folding the half-circle into thirds. Cut along the 13-fold lines and trim the ends to make a rectangle. 2. Using a pencil (ink from…
The write-up says “A C18-silica column is used in this experiment, a 0.46 x 15 cm column with 5-µm particles. Equilibrate the column with 20 empty column volumes of 0.010 M phosphate buffer (pH 7.2) at a flow rate of 1.2 mL/min before beginning chromatography.” Show the calculation for how much mobile phase you would use (volume) and how long it will take to equilibrate the column.
When utilizing silica gel column chromatography to separate compounds, which component is expected to elute from the column first and why?
To compensate for a complex or unknown matrix, the ● · · ● A. Calibration curve OB. Standard addition Method O C. Internal Standard Method O D. Dilution method O E. Least-Squares Analysis O F. Standardization method should be used to determine the analyte concentration.
Very low concentrations of perchlorate gave the following ion chromatography readings: 174, 178, 153, 192, 180, 166, 105 Seven blanks had a mean reading of 45.0 What is the signal detection limit for this method? report your answer to the nearest whole number
You must separate three different compounds with reversed phase HPLC. Compound 1 is an acid (pKa = 4.3), compound 2 is neutral compounds and compound 3 is a base (pKa = 9.6). As eluent, use 30/70 (v / v)% methanol / pH 3.0 formic acid buffer. The retention time and the top width at the base of the top for the three components are presented below. You can assume the dead time to 1.2 minutes in your calculations.Compound Retention time [minutes] Peak width [seconds] 1 10.1 282 5.0 143 6.1 17a) Calculate the efficiency (number of theoretical bases) for component 1.b) Calculate the selectivity and resolution between components 1 and 2.c) When you increase the pH of your eluent to pH 6, how will the retention be affected (increase, decreaseor unchanged) for the different associations (1, 2 and 3) ?, justify your answer.d) How retention factors are generally affected by an increase in the proportion organicallymobile phase solvents for reversed phase HPLC separations ?, justify your…
In a HPLC separation of two compounds, A and B, the retention times observed are 3.5 min. for A and 4.5 min. for B on a 15 cm column. The retention time for the mobile phase is 1.0 min. The peak widths (at the base) for A and B are 0.5 and 0.7 min respectively. Calculate the following: (i) The capacity factor of A and B. (ii) The peak resolution. (iii) The average number of theoretical plates in the column
1. Methanol and ethanol are separated in a capillary GC column with retention times of 370 and 385 s, respectively, and half widths (W₁/2) of 9.42 and 10.0 s. An unretained butane peak occurs at 10.0 s. Calculate the separation factor and the resolution.
A student performed three DCM layer titrations in Part 2 and they reported the following measurements: Final Burette Reading Initial Burette Reading Volume of DCM Aliquot Final Burette Reading Initial Burette Reading Volume of Sodium Thiosulfate Determination #1 Determination #2 Determination #3 29.99 mL 22.78 mL 7.21 mL 28.56 mL 1.21 mL 27.35 mL 37.45 mL 29.99 mL 7.46 mL 28.89 mL 1.08 mL A 27.81 mL 44.86 mL 37.45 mL 7.41 mL 28.68 mL 1.00 mL 27.68 mL Which determinations were the student's 'best two'? Calculate the percent difference for the 'best two' and show the complete calculation. Note that the concentration of standard sodium thiosulfate, which the student used, is unknown.
Ab 23.
Create a separations flowchart for qualitative analysis for the following Sb3+ Fe3+ Zn2+ Al3+ Cd2+