please send correct answer Q10 QUESTION 9A researcher is working on sustainable composites has developed an experimental composite (CFRP) that has a small amount of biodegradablematrix. During a lab accident, they have lost some directional properties values that they have measured experimentally. However, they found theirnotes that include information on the Poisson's ratio, the stiffness matrix, and the ratio of E2/E1. Using the information provided find the value of E1 inGPa.V12 = 0.34E2/E1 = 0.13Q11= 132.04 GPaQ12=2.52 GPaQ22=8.92 GPaQUESTION 10According to the rule of mixtures, a composite has a tensile strength of 2214 MPa. If the strength of the fibres is 3700 MPa and the strength of thematrix is 64 then what is the volume fraction of the fibres in the composite?

Answered: Image /qna-images/answer/eb738766-96a4-4fcd-8d21-9c143ba440e6.jpg

According to the rule of mixtures, a composite has a tensile strength of 2214 MPa. If the strength of the fibres is 3700 MPa and the strength of the matrix is 64 then what is the volume fraction of the fibres in the composite?

According to the rule of mixtures, a composite has a tensile strength of 2214 MPa. If the strength of the fibres is 3700 MPa and the strength of the matrix is 64 then what is the volume fraction of the fibres in the composite?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need the answer for number 10.
60 30 e Draw the Front, Top and Right side Views for the given Body using scale 1:1 , all dimensions are in millimeters. 22 36 60 020 R25 110 40
I need these three parts answered (Multiple Choice). If you can not answer all three parts please leave it for another tutor to answer. Thank you. For the two holes identified as datum D, what is the total size tolerance specified for those holes? (Multiple Choice)a. .002'b. .003'c. .004'd. .006' The two holes identified as datum D have a counterbore on one end. What size toleranceis specified for the counterbore diameter? (Multiple Choice)a. .010″ (±.005″; see title block)b. .020″ (±.010″; see title block)c. .030″ (±.015″; see title block) What letter represents the revision status of this print? (Multiple Choice)ABCD
Please show the complete solution and use all the decimals in solving.
can you redo D please with the actual answer
PLEASE DO THIS TYPEWRITTEN AND COMPLETE IT, I WILL UPVOTE. IF NOT COMPLETE AND TYPEWRITTEN, NO UPVOTE. THANK YOU
Question 16 Here is a way we can estimate the distance from the earth to the moon. When the moon is seen at its zenith at a point A on the earth, it is observed to be at the horizon from point B. Points A and B are 6152 miles apart and the radius of the earth is 3960 miles. 20 Earth 0= B a) Calculate the angle in radians. (Round your answer to 5 decimal places.) d= ? v Moon Details b) Estimate the distance from point A to the moon using your angle from part a). (Round your answer to the nearest thousand.) ?
What is the force member in LC1 in N?
5. Given the following sentence descriptions of the geometric tolerance information, correctly sketch the feature control frames for each. a. The feature must be flat within a tenth of a millimeter tolerance zone. b. The feature must be straight within a thousandth of an inch tolerance zone. c. The feature must be round within five-tenths of a millimeter tolerance zone. d. The feature (planar surface) must be perpendicular within a five-thousandths of an inch tolerance zone relative to datum feature A. e. The feature (axis of a cylinder) must be perpendicular within a one-hundredth of a millimeter cylindrical toler- ance zone at maximum material condition relative to datum feature D. f. The feature (planar surface) must be parallel within a thousandth of an inch tolerance zone relative to datum feature A. g. The feature (axis of a cylinder) must be parallel within a three-hundredths of a millimeter cylindrical tolerance zone at maximum material condition relative to datum feature M. h.…
f) Answer the question shown in the images. Show every step
please hand written solution please hand written solution please hand written solution