According to measured values given in following table, caculate the value of resistivity for each wire. Wire No R,(2) 4 (mm) L, (mm) Lwire (mm) rwire (mm) 1 935 1000 – 935 1000 0.25 2 485 1000 – 485 1000 0.175 3 795 1000 – 795 1000 0.35 4 794 1000 – 794 1000 0.35 664 1000 -664 1000 0.25 886 1000 – 886 1000 0.5

According to measured values given in following table, caculate the value of resistivity for each wire. Wire No R,(2) 4 (mm) L, (mm) Lwire (mm) rwire (mm) 1 935 1000 – 935 1000 0.25 2 485 1000 – 485 1000 0.175 3 795 1000 – 795 1000 0.35 4 794 1000 – 794 1000 0.35 664 1000 -664 1000 0.25 886 1000 – 886 1000 0.5

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.21MCQ

See similar textbooks

Similar questions

Determine the voltage across the resistor, the current in the resistor, and the output voltage in figure 1 and figure 2. Plot these waveforms with proper ac cycle phase alignment. 1SR154-400 is a silicon rectifier 1 ampere diode. Indicate the peak values as per calculation.
a. If you do not go completely around the loop when applying Kirchhoff’s voltage law, then the algebraic sum of the voltages cannot be determined the algebraic sum of the voltages will always be positive the algebraic sum of the voltages will always be negative the algebraic sum is the voltage between the start and finish points b. A p -type semiconductor is a semiconductor doped with impurity atoms whose electron valence is +4 pentavalent impurity atoms trivalent impurity atoms
Check all the correct statements. The forward voltage in diodes is larger than its reverse voltage. The forward voltage in diodes is due to the neutral zone between the two types of semiconductors used in diodes. The forward voltage in diodes is smaller than its reverse voltage. The forward voltage in diodes is due to the depletion region
Give a conclusion about clipper circuits and clamper circuits.
Produce a working circuit with the Integrated Circuits shown in the image.
Diodes Si diodes will be considered. Which of the following is wrong I. D3 diode blocking. II. Diode D3 is on. III. Diode D4 is conducting. IV. Diode D4 is in blocking.
Write down the names of Fabrication steps and explain the lithography process briefly.
Could some please provide an explanation for VL why 15 and 1.33
YEN A docs google.com/presentalionvu/109aRdVPOGDKPIlowJ800-G gwlgdTPyTSE OLaSFDGy/edit A Classes Aplitude Questiors. O www.tce.edu I IVIVA a AMAZON E FUPKART SkiRack.com How to pass a 2D a. G operi ended behavi. E Rectifying Diodes. * NASSCOM FutureS.. I VIRTUAL ELECTRON. 白 Q1 For the op-amp circuit shown below V is approximately equal to 10 V 105 0 95 2 1 ΜΩ 100 kN 上 100 k2 95 2 105 N 1 M2
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
These Insulators are used when equal Voltage is required across each Insulator unit. O A. RADING INSULATORS O B. GRADING INSULATORS O C. STRAINING INSULATORS O D. GAINING INSULATORS
Please make a concept map of the covalent link theme for semiconductors with the following subtopics, you can add tables, graphs, images, or things you think are relevant 1.5 Driving process 1.5.0 Introduction 1.5.1 Mobility 1.5.2 Relationships between carrier equilibrium concentrations 1.5.3 Detailed balance principle 1.5.4 Carrier equilibrium concentrations in homogeneous semiconductors 1.5.5 Conductivity 1.5.6 Hall Effect