A.W 4 A simple beam on a 10 ft span supports a uniform load of intensity 800 lb/ft (see figure). The beam consists of a wood member (4 in. × 11.5 in. in cross section) that is reinforced by 0.25 in. thick steel plates on top and bottom. The moduli of elasticity for the steel and wood are E, 30 × 10° psi and E, = 1.5 × 10° psi, respectively. Calculate the maximum bending stresses o, in the steel plates and o, in the wood member due to the uniform load.

A.W 4 A simple beam on a 10 ft span supports a uniform load of intensity 800 lb/ft (see figure). The beam consists of a wood member (4 in. × 11.5 in. in cross section) that is reinforced by 0.25 in. thick steel plates on top and bottom. The moduli of elasticity for the steel and wood are E, 30 × 10° psi and E, = 1.5 × 10° psi, respectively. Calculate the maximum bending stresses o, in the steel plates and o, in the wood member due to the uniform load.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the given properties of beam below. Compute the flexural capacity of the beam. b = 390mm d = 440mm d' = 80mm fc' = 34.5MPA fy = 350MPA As = 4 - 40mm As' = 2 - 32mm A. USE NSCP 2001, Mu = kN-m B. USE NSCP 2015, Mu = kN-m
NEED ANSWER ASAP!! A so-called "trapeze bar" in a hospital room provides a means for patients to exercise while in bed (see figure). The bar is 2.1m long and has a cross section in the shape of a regular octagon. The design load is 1.6kN applied at the midpoint of the bar, and the allowable bending stress is 240 MPa. Determine the minimum height h of the bar. Round to one decimal place. (Assume that the ends of the bar are simply supported and that the weight of the bar is negligible.) hmin=___mm
A contractor has ordered a composite beam. The beam is constructed of Douglas Fir wood and two plates of Stainless 304 steel. The allowable bending stresses are as follows: (Oallow)w = 22 MPa (Oallow) st = 140 MPa What is the maximum moment that can be applied to the beam (in kN-m)? Express your response using three significant digits. y 150 mm M 30 mm 80 mm 30 mm
O FS = 2.4 O FS = 2.2 Consider a simple supported beam subjected to the load shown. The beam has a solid square cross-section with edge "a", and made of steel alloy having a yielding tensile and compressive strength of oy = 400 MPa. Determine its minimum required edge "a" for a factor of safety against yielding FS = 2.5. The area moment of inertia of that section about its neutral axis N.A. is INA = b.h³/12. of 3 kN 2 kN/m D 6 m + Select one: 5:37 PM 86°F Light rain ENG 6/18/2021 hp
3) The simply supported beam with the cross-section as shown supports a total uniformly distributed load of 4P and 2P and concentrated load P as shown in the figure. Determine the maximum allowable value of P if the allowable flexural stresses are limited to 35 MPa in tension and 150 MPa in compression respectively. 1m P B 1m IC 4P 3m D 2P 1m DE U 175 200 (Dimensions in mm)
A simply supported wood beam, reinforced with steel plates, has the cross section shown. The beam carries a uniformly distributed load of 16 kN/m over the middle half of its 4-m span. If modular ratio is equal to 15, determine the largest bending stresses in the wood and steel. 96 mm 96 mm -200 mm 8 mm 240 mn 8 mm
Please answer the question correctly and pleaase put the answer on the paper. Thank you Note: The tolerance is ± 1 in the third significant digit. Put the exact answer
How to solve this question step by step
A cantilever beam having a 4m span carries a uniformly distributed load throughout its length. The beam is A36 steel with yield strength Fy = 248 MPa. The beam is not restrained against lateral buckling. The beam is W 21 by 62 steel shape, whose relevant properties are shown below: r = 0.053 m d = 0.533 m bf = 0.210 m tf = 0.016 m S = 0.002077 m3 Given this condition, solve for the allowable flexural stress in the compression flange. Use Cb = 1 as should be taken conservatively
help me solve this in 30 mins pls
Calcualte the following: Total factored floor load in 2 decimal places, ___ kPa Total factored uniform load on girder GH in 2 decimal places, ___ kN/m Maximum ultimate bending moment at discontinuous end of girder JK to the nearest whole number = ___ kN·m
The stiffness matrix of the beam shown below is - 1. (2 В El 2EI 4m 8m A.