a. Trueb. FalseQ3/A: For the power system shown, calculate fault current and when a 3-phase fault occursat point F. The data are given below.EquipmentXIX2XOXnRatingG20%20%6%2.5050 MVA-11 KVΤΙ10%10%10%11/132 KV,30 MVALINE100010003000T210%10%10%132/11 KV,30 MVAMI25%25%6%40 MVA,11KVM225%25%6%40 MVA,11KVT2™KT1GLineFault+M1M1

Answered: Image /qna-images/answer/a8d9e36b-5d6e-43f3-b074-01903496b5e9.jpg

a. True b. False Q3/A: For the power system shown, calculate fault current and when a 3-phase fault occurs at point F. The data are given below. Equipment XI X2 XO Xn Rating 20% 20% 6% 2.50 50 MVA-11 KV ΤΙ 10% 10% 10% 11/132 KV,30 MVA LINE 1000 1000 3000 T2 10% 10% 10% 132/11 KV,30 MVA MI 25% 25% 6% 40 MVA,11KV M2 25% 25% 6% 40 MVA,11KV T2 ™K T1 Fault G Line M1 M1

a. True b. False Q3/A: For the power system shown, calculate fault current and when a 3-phase fault occurs at point F. The data are given below. Equipment XI X2 XO Xn Rating 20% 20% 6% 2.50 50 MVA-11 KV ΤΙ 10% 10% 10% 11/132 KV,30 MVA LINE 1000 1000 3000 T2 10% 10% 10% 132/11 KV,30 MVA MI 25% 25% 6% 40 MVA,11KV M2 25% 25% 6% 40 MVA,11KV T2 ™K T1 Fault G Line M1 M1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

How do I convert the following per unit voltages to actual voltage?
Q15
3. Machines 1 & 2 --- 100 MVA, 18 kV, X"=X2=0.3, Xo= 0.07 pu Machine 2 Xn = .1 pu Transformers ------ 100 MVA, 20-345Y kV X=0.1 pu Line 2-3 z1=1+j120 ohm zo= 2+j300 ohm Machine 1 Kary 1 T₁ 2 2013 FY-Y (3) T₂ TO A A. Develop a base table with a 100 MVA, 345kV base in the Line. Machine 2 Kroooy
a) In Three Phase Faults that will occur separately on A, B, C and D Busbars, Calculate the currents. b) Maximum fault currents to pass through KA, KB, KC1, KC and KD Protection devices determine. Help me please... Thank you so much.
The negative sequence current of a solidly grounded generator for single line to ground fault is j 2.5 p.u. Then the positive sequence current during the fault is equal to o j7.5 pu o jo.75 pu o j2.5 pu o jo.25p.u
72. In 132 kV system, the phase to ground ca- pacitance is 0.01 µF and inductance is 6H. The voltage that appears across the contacts of circuit breaker if a magnetising current of 10A is interrupted is (ii) 356 kV (iv) 176 kV (1) 156 kV (iii) 245 kV
Which of the following characterizes series faults? All of these Imbalance in series impedance No connection between lines No connection between lines and neutral
The reactance data for the given power system is as follows: Item G₁ G₂ Ti T2 X¹ X² xº 0.10 0.10 0.05 0.10 0.10 0.05 G₁ 0.25 0.25 0.25 0.25 0.25 0.25 Line 1-2 0.30 0.30 0.50 T2 2 -+*+ & D 41 A bolted single phase-to-ground fault occurred at bus 1. Compute the fault current in per unit. 3 Τ 1 to coto 4 G₂
A 15 MVA, 6.6 kV, wye connected generator has X 1 = X 2 = 20%and X 0 = 10%. The neutral of the generator is groundedthrough a reactor of 5% reactance based on the generatorrating. A double line-to-ground fault occurs at terminals band c. What is the current in the ground?
A) Calculate the breaking capacity and making capacity if maximum value of AC 500 A and DC component is 50 A. B) Calculate the short circuit MVA that is fed into the system due to fault at point F. 22 kV/ 66 kV 3000 kVA 10% F 2000 kVA 8 %
Solve asap I'll rate