has X 1 = X 2 = 20% and X 0 = 10%. The neutral of the generator is grounded through a reactor of 5% reactance based on the generator rating. A double line-to-ground fault occurs at terminals b and c. What is the current in the ground

Q: In single phase power factor meter there is error due to frequency and waveforms but not in three…

A: It is given that:Why there is an error due to frequency and waveforms in the single-phase power…

Q: Loss of excitation is one of the stator faults of alternator which is operational at power station O…

A: 1)Loss of excitation is one of the fault on rotor. 2)Loss of excitation is a very common fault in…

Q: In DC generator pole core is made up of

A: In the DC generator pole core is made up?

Q: Discuss the advantage and disadvantage of each connection. Generator reactor Tie-bar…

A: The advantage and disadvantage is given below of the following : Generator reactor: Disadvantage:…

Q: The loss of generation in a generator which is meeting a huge amount of demand in small grid is…

A: In small power plant loss of generation is directly affect the load and after the loss of generation…

Q: Zero sequence currents can flow from a line into to a transformer bank if the windings are delta /…

A: Zero sequence current will flow into a star winding only when it's natural is grounded.  Zero…

Q: a generator has a capacity of 2000KVA and 10% of internal percentage reactance, for symmetric fault…

A: (MVA)old = 2000 MVA (MVA)new = 5000 MVA %Xold = 10 %

Q: D.C shunt generators are most suitable for arc winding

A: The most suitable DC genrator for arc welding is Differential compund genrator.

Q: 2. When a large shunt capacitor is suddenly connected in parallel with the load bus in the…

A:

Q: 6. A 3 phase fault occurs at point F as shown in figure. Determine the critical clearing angle for…

A: Given figure, 3 phase fault occurs at point F as shown in the figure. The generator is delivering…

Q: The _____________________ of transformers are neglected to draw the reactance diagram. a-Shunt…

A: This is based on the fill the blank  The _____________________ of transformers are neglected to draw…

Q: are used across an inductive and capacitive loads so as to supply part of the reactive VARS required…

A:

Q: disadvantage of Phase Locked Loop is

A: The input signal phase is developed in the output signal using a control system, this is done by a…

Q: A 400 V, 3-phase alternator is subjected to an unsymmetrical fault. The

A: Ia=Ia0+Ia1+Ia2Ia=-j10+j6+j4=0Therefore , it is Double line to ground fault Fault current is -…

Q: What is the Shunt de generator and Draw equivalent circuit?

A: In DC generator field current is needed to excitation. DC field current excited separately through…

Q: A three phase generator is operating at 1500rpm and has a no-load voltage of 7 kV. What would be the…

A: In this question, we need to choose the correct option.

Q: the slip-rings replaced by separated segments In order to generate a bidirectional Voltage true /…

A: This statement is true or false?  "the slip-rings replaced by separated segments In order to…

Q: If the core loss of single phase transformer at full load is 284 W, then the core loss at 25% of…

A: Core losses at full load = 284W. Find the core losses at 25% load?

Q: QUESTION 19 E-06, PC-02. Three inductors 15 mH, 15 mH and 15 mH are connected in series. What is the…

A:

Q: in a tie-bus arrangement as shown in figure. the reactances of the generators and reactors are 0.2…

A: We redraw the circuit on per phase per unit basis: In the circuit the fault point is connected to…

Q: Eddy current losses can be reduced by making the core of a stack of plates electrically insulated…

A:

Q: True or False Due to their shape, full-pole generators are more affected by wind and centrifugal…

A: Due to their shape, full-pole generators are more affected by wind and centrifugal forces than other…

Q: A 13.2 kV, 60 Hz, 3-phase synchronous generator is connected in star and its neutral point is…

A: Given, The supply voltage (E)= 13.2 kV(rms)  Frequency (f)= 50 Hz  Per phase inductance (L)= 0.02 H…

Q: In medium transformers, the total iron losses may vary from. rated output. % of the 0.4 to 1 O 0.2…

A: The iron loss of the transformer is defined as the sum of the hysteresis current loss, eddy current…

Q: Thyristor regulators A.C TYPE GENERATORS GENERATOR TYPES ACCORDING TO THE NUMBER OF PHASE

A: Thyristor regulators Thyristor power controllers (SCR power controllers) control power & voltage…

Q: In transformer, is defined as the change in the A7 secondary terminal voltage from no-load to…

A: in transformer, ..... is defined as the change in secondary terminal voltage from no load to full…

Q: the core loss of single phase transformer at full O 52W O 105W O 13W O 210W

A: In transformer, mainly two losses present namely core and copper losses.

Q: Adjustment resistance in rotor system will --------when three phase load .decrease Increase O not…

A: Adjustment resistance is also known as external resistance. Purpose of adding external resiistance…

Q: 2A. What is another term for "shunt"? a) in series b) in parallel c) compounded d) none of the above…

A:

Q: 210⁰ and Ic=980 cis - 60°. Find the negative sequence of phase B current. 11. The phase B current of…

A: In this question we need to find a current in line B

Q: False True the slip-rings replaced by separated segments In order to generate a bidirectional…

A: "The slip rings replaced by seperated segment in order to generate a bidirectional voltage" This…

Q: explain why Transformers are necessary in all stages of power distribution systems. Three-phase…

A: Given: Transformer: Transformer is a static device used for the transfer of varying voltage and…

Q: If the core loss of single phase transformer at full load is 39 W, then the core loss at 25% of load…

A: Need to find the core loss of Transformer at 25% of the load

Q: For the same alternator the ratio of rated kva, when connected as a three phase winding alternator…

A: Solution: When connected to single-phase winding, Let the number of turn/Phase=N Phase Spread…

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.