A WT305 x 41 standard steel shape is used to support the loads shown. Assume w = 60 kN/m, LAB = 1.4 m, LBC = 2.8 m, and LCD = 1.4 m. Consider the entire 5.6 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer).

A WT305 x 41 standard steel shape is used to support the loads shown. Assume w = 60 kN/m, LAB = 1.4 m, LBC = 2.8 m, and LCD = 1.4 m. Consider the entire 5.6 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5c and 5d
The dimensions of a rectangular beam are limited to b = 300 mm and effective depth, d = 700 mm. Using f’c = 28 MPa, long bar fy = 415 MPa, calculate the required amount of tensile reinforcement so that a tensile strain of 0.005 is attained under a sustained ultimate bending moment of 1,200 kN.m. Compression bars centroid is 70 mm from beam edge. 4,387 3,839 6,180 5.353
Please draw shear force diagram v(X) and bending moment diagram m(X)
What is the maximum length of a uniformly loaded, simply supported beam based on the maximum allowable stresses, its normal stress of 90MPa and its shear stress of 100MPa? The uniform load is 10kN/m. The area is b = 20mm and h = 80mm
From the given figure below, determine the minimum width of the beam if the flexural stress is not to exceed 150MPa. Assume height of beam is 300mm. 40KN k pº RB=320kN 280KN 2M 65100/m -40kN -BOKNM 4m 20KN 도 20KN qu 520 kNm RD = 260KN V-DIAG -260kN M-DIAG
Find the Magnitude of the Maximum Shear Stress in the below beam and cross-section, if: W = = 6 kN/m L = 5 m b = 55 mm h = 144 mm Ensure that your answers are in MPa. Mo W Cross-Section: L b h
For the steel beam and loading shown above (A = hinge support, C = Cable) (A) Write the equations for bending moment and shear force at any section along the beam and draw the shear force and bending moment diagram. (B) Assume a rectangular beam cross section of 25 x 25 mm, what is the maximum bending stress
Draw the shear force and bending moment diagrams for 2 kip the beam under the external loadings shown in the figure. 200 lb/t Note use the graphical method; show all the critical tuming points of each curve, along with the calculation steps used in determining the critical points. 9
Could anybody solve this problem and expaine please?
A beam has a bending moment of 3 kN-m applied to a section with a hollow circular cross-section of external diameter 3.4 cm and internal diameter 2.4 cm . The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.6 cm from the neutral axis Solution: (i) The moment of inertia = ii) The radius of curvature is (iii) The maximum bending stress is in (N/mm^2) Answer and unit for part 3 iv) The bending stress at the point 0.6 cm from the neutral axis is in(N/mm^2) Answer and unit for part 4
A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of external diameter 3.6 cm and internal diameter 2.4 cm . The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.5 cm from the neutral axis (i) The moment of inertia = ii) The radius of curvature is (iii) The maximum bending stress is iv) The bending stress at the point 0.5 cm from the neutral axis is
2. A cantilever of length 5 m carries a UDL of 2 KN/m over the whole length and a point load of 4 KNm at the free end. Draw the shear force and bending moment diagrams for the cantilever. [Max. SF = 14 KN; Max. BM =-45 KN-m] %3D 3. A cantilever 2.5 m long carries a UDL of 60 KN/m at a length of 1.8 m from the free end. Draw the shear force and bending moment diagram.