nd the magnitudes of the support reactions of the beam, shown on e fig. Dimensions and loads are respectively L=2 m, F=5√2 N, =3 Nm, q=4 N/m. SL M XB

Q: when does effusion happened in a vacuum  system and vacuum pomp?

A: Given :-  when does effusion happened in a vacuum  system and vacuum pump...

Q: d casting of the part whose perspective pictures are given below, take into account the surface of…

A: The casting consist of a hole so we need to make a core as shown below.

Q: Suggest a full procedure to explain how to produce the mechanical part in the figure by casting step…

A:

Q: Q3: Explain how you would produce a hard surface in the followings, Give reason(s) for your…

A: Given question: Q3. Explain how you would produce a hard surface in the following, Give reasons for…

Q: Compare the rapid and slow freezing in details .

A: Freezing is defined as a phase transformation process in which heat is extracted from a liquid to…

Q: 2.1 What is the benefit of using investment casting for the production of a turbine rotor compared…

A: As per the Bartleby answering guidelines we are supposed to answer only first three sub parts of the…

Q: Q3: Explain how you would produce a hard surface in the followings, Give reason(s) for your…

A: Given question: Q3. Explain how you would produce a hard surface in the following, Give reason for…

Q: Which of the following manufacturing methods could be economical for a batch size of 100,000 units?…

A: We know that the batch size of 100,000 units is a mass production type. For mass production we need…

Q: 3- Calculate the number of finished goods (output) or N for the figure illustrated below:

A: Given: Total number of goods xi = 1200 Goods accepted after casting = 90% = 0.9 Goods sent for…

Q: What would the solution be if TB was in the other direction ?

A:

Q: What is the appropriate way to determine the information inside a sand casting? Explain that. NS. If…

A: Sand Casting:- Mould material-sand Binders- clay, silica, corn flour For making a sand casting a…

Q: time required to fill the mould

A: Given; A mould has downsprue:Velocity of mould cavity=1500 cm3Velocity at base of sprue, V=2ghArea…

Q: B-Write (True) or (False) for the following sentences: 1. Cast-cobalt Alloys tool are produced by…

A: to Write (True) or (False) for the following sentences:Cast-cobalt Alloys tool are produced by…

Q: Hot working is a process commonly seen in the production floor that usually involved heating…

A: Hot working progresses the engineering properties of the workpiece since it replaces the…

Q: What would ne faster to produce a large quantity of these boxes? Batch production or constinous…

A: Batch production: In batch production, the product is manufactured in a definite amount and definite…

Q: A mould has downsprue whose length is 20 cm and the cross sectional area at the base of the…

A: Length of the sprue, h=20 cm or 0.2 mCross sectional area at the base of the downsprue, A=1 cm² or…

Q: why is the feeder used in the casting process? what is its significance and how should it be…

A: Casting process is a manufacturing process in which molten metal is poured into the cavity which is…

Q: What is the advantage in casting turbine blades that have either highly aligned grain boundaries or…

A: Turbine blades are manufactured by casting by containing superalloys in them. These superalloys have…

Q: Q4- Why the additive clay add to sand in casting? 0s In

A:

Q: Shear modulus is similar to O work hardening O percent reduction in area O Avogadro's number O…

A: Shear modulus When a force is applied parallel to one of a solid's surfaces while an opposing force…

Q: Q3: Explain how you would produce a hard surface in the followings, Give reason(s) for your…

A: Given question: Q3. Explain how you would produce a hard surface in the following. Give reason for…

Q: 6) is a sheet metal forming process performed by placing a sheet-metal blank over a die cavity and…

A: Only four to five multiple questions are allowed to solve.

Q: What are the functions of base flange, edge flange, fillet, mirror, sheet metal gusset, embossing…

A: To write: The functions of base flange, edge flange, fillet, mirror, sheet metal gusset, embossing…

Q: Write down the Experiment “Introduction to Casting Processes and study various stages of casting…

A: In a manufacturing engineering, casting is a process in which molten metal poured into a mould,…

Q: The primary energy consumption in 2018 in the united states was 129,373 kToe and the final energy…

A: Given,  Primary energy consumption= 129,373 kToe  Final energy consumption = 82,192 kToe  Time…

Q: What is K-factor in sheet metal operation? Mention its value.

A:

Q: A moterial is crushed in a Gyratory crusher such that the averoge size of particle is reduced from…

A:

Q: Draw TWO (2) casting processes that would be most suitable for making a gold and jewellery

A: 1- lost wax casting also known as investment casting.

Q: Write the requirements of good pattern. 2. What is core venting?  3. Which process is called lost…

A: 1.Requirements of good patterns :a. It helps in creating good shape.b. offers good strengthc. helps…

Q: we need to measure the product regarding to the phys

A: Product: Product engineering is the process of creating a device, assembly, or system in order for…

Q: For the casting of the part whose perspective pictures are given below, take into account the…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.