(c) What is Vmax and where in x is it located? (d) What is Mmax and where in x is it located?

Q: A motor operates at 1800 RPM and expends 2 HP.  How many ft-lbs of torque does it provide at that…

A: Given data: The speed of the motor is; N=1800 RPM. The power of the motor is; P=2 HP.

Q: Find the value of a. TO a. Vs +3

A:

Q: The dot product of two unit vectors: (The answer cannot be found on the other choices.) always has a…

A: When the dot product of any two vectors is equals to 1 then those vectors are in same direction…

Q: Consider the connection at D. What kinds of reactions can act on member AB at the connection? Click…

A: Given:Connect at DDiagram is givenTo find:kind of reactions at member AB

Q: Figure 1. Length of line AC? Zradis 8.33" 10 5.83" 9.72" 11.33" Figure 1. Value of angle <BAC in…

A:

Q: D Question 2 Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your…

A: Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your paper and…

Q: Add the vectors using triangle rule or parallelogram rule

A: Draw the diagram of the vector system.

Q: Question 18 Simplify (−4 − 4j) O 1.412-45° O 1.41/225° O 1.414-225° O 1.41/45°

A: Simply the above expression

Q: PO 8 in.

A: Redraw the following figure for the given question.

Q: Q3/ For the plate shown in figure below find (a) E A Y수 4 6 X 7 5

A: Let us consider the given figure , divide into two parts of area A1 and A2 The sum of area ΣA can be…

Q: Draw the front, Side and top

A: We need to draw three orthographic projection views.

Q: Write the general equation of the circle of center (0, 4) and radius 4. Figure is not required.

A: The generalized equation of a circle with centre at origin and radius = r units is as given below:…

Q: A plastic rod AB of length L = 520 mm has a diameter d, = 30 mm as shown in Figure Q2(b). A plastic…

A: For the given composite bar it is required to determine: (1) Total elongation of the bar when P = 15…

Q: If the taper angle, large diameter, smaller diameters are respectively 2°, 44 mm, and 34mm. Find the…

A:

Q: For the objects shown below sketch the object in the space provided after rotating it about the axis…

A: Find Rotate the object about the given axis.

Q: 1-23.Determine the length of side C of the triangle shown in Figure P1-23.

A:

Q: 5. (a) (i) A crane hook with a mass of 80 kg exerts a vertical force F downward at A (see Figure…

A:

Q: The landing gear system of a plane is made of an actuator AC and 2 rods CB and OAB. They are pin…

A:

Q: 4. Determine the length of stroke of a slider E when the crank AC rotates by 30 degrees in counter-…

A: Find the attachment for the solution.

Q: Determine eq.uations and frequuency for the following figure

A:

Q: Using the rules of projection find the true length of line AB using a 1:5 METRIC scale.

A: Given condition

Q: n the figure, front (1st picture) and left (2nd picture) views of a machine part are given. Based on…

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: solve 4 and 5 only

A: The given state of stress is:To find:(iv) The orientation of the elements for the maximum in-plane…

Q: FAB Find the Angle between Line AB and Line AC in degrees. (Hint: Dot Product).

A:

Q: how do you know where the point 2 is ? or how do you find point 2

A:

Q: 1-8. Determine angles a, b, and c (Figure P1-8). a 35° FIGURE P1-8

A:

Q: displacement (throw) of the wheel assembly.

A:

Q: Solve both and show all parts and solutions

A: The power to input shaft is The speed of gear of input shaft is The gear ratio is The loss in power…

Q: Question 3) On the  plate in the figure, the length  L  is given as L=72 m . According to this;…

A:

Q: solve a thru e show all steps

A: is normal reaction force between contacting surfaces.W is the weight force of the block. is the…

Q: Find Rab for the circuit fn figure. 202 202 Rab 792 252

A: The circuit is shown below.

Q: Gear 2 in the diagram below is driven at a speed of 126 revolutions per minute. Gear 2 has 16 teeth,…

A: The gear train is simple,The speed ratio of a simple gear train with 2 gears is as follows,Here,N is…

Q: calcula la formula del momento en C Cx L3 L Cy B FAB L4 0₂ 0 W

A: Calculate the formula for moment at C.

Q: Find the x-component of F1 in Newtons. Find the y-component of F1 in Newtons. Find the z-component…

A: The data given is, F1=400 N ϕ=41° θ=36°

Q: can the solve the last three quetsions please

A: mass of refrigerant R-22, m= 2kgThe initial pressure, P1= 6.8 barThe initial state is saturated…

Q: If the taper angle, large diameter, smaller diameters are respectively 2°, 44 mm, and 34mm. Find the…

A:

Q: Question 3) The length L is given as L=34 m on the plate in the figure. According to this; Question…

A:

Q: I tried the degree both 51 and 50.99 but it is incorrect. Plz help.

A:

Q: Consider for the part in the figure below, a =112, b= 60 and c= 104. 80 Dimensions in mm Analyze the…

A:

Q: Solve erf only

A: Given:To Find: the value of x.Note: In the above equation,

Q: Q1/3-The B Rep. Scheme for the box consists of: * O 8 faces, 8 edges & 12 vertices O 6 faces, 8…

A: B rep is often known as Boundary representation. This scheme is based on the concept that a physical…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.