A wooden beam is fabricated from one (2 x 10 in) and two (2 x 4 in) pieces ofdimension lumber to form the l-beam cross section shown in Figure. The flangesof the beam are fastened to the web with nails that can safely transmit a force of(120 Ib) in direct shear. If the beam is subjected to a shear force of (500 Ib),determine the maximum the maximum shear stress in the l-beam. Use l = 748in44 in.2 in.2 in.10 in.2 in.Nails50.3 psi O24.4 psi45.3 psi O12.0 psi O

Answered: Image /qna-images/answer/e83ac042-bc1f-40c7-bdf5-de9a6453d2f8.jpg

A wooden beam is fabricated from one (2 x 10 in) and two (2 x 4 in) pieces of dimension lumber to form the l-beam cross section shown in Figure. The flanges of the beam are fastened to the web with nails that can safely transmit a force of (120 lb) in direct shear. If the beam is subjected to a shear force of (500 lb), determine the maximum the maximum shear stress in the l-beam. Use I = 748 * .in4 4 in. 2 in. 2 in. 10 in. 2 in. Nails 50.3 psi O 24.4 psi 45.3 psi 12.0 psi O

A wooden beam is fabricated from one (2 x 10 in) and two (2 x 4 in) pieces of dimension lumber to form the l-beam cross section shown in Figure. The flanges of the beam are fastened to the web with nails that can safely transmit a force of (120 lb) in direct shear. If the beam is subjected to a shear force of (500 lb), determine the maximum the maximum shear stress in the l-beam. Use I = 748 * .in4 4 in. 2 in. 2 in. 10 in. 2 in. Nails 50.3 psi O 24.4 psi 45.3 psi 12.0 psi O

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported wood beam, reinforced with steel plates, has the cross section shown. The beam carries a uniformly distributed load of 16 kN/m over the middle half of its 4-m span. If modular ratio is equal to 15, determine the largest bending stresses in the wood and steel. 96 mm 96 mm -200 mm 8 mm 240 mn 8 mm
AW410 x 60 standard steel shape is used to support the loads shown on the beam in the figure. Assume P = 130 kN, w = 27 kN/m, a = 2.8 m, and b = 2.0m. Determine the magnitude and location of the maximum bending stress in the beam. A max = x = a i i B a → Pin |C * b W MPa m D a E
A3-m long steel plate having a cross-section of 25 mm x 300 mm is used as a hanger and subjected to a tensile load of 1070 KN. Poisson's Ratio = 0.25 and E = 200 000 MPa. Compute the total lateral deformation in mm (along the 300 mm side). Express your answers in 4 decimal places.
6.59 A square section as shown in the figure below is subjected to bending moment M. (c) Obc = Obl y || h y H What is the maximum bending stress? (a) Obc = obt 12M h³ 9M 2h³ JXC h (b) bc = Obt = (d) %bc =%bt = 6M 4³ 9M h³
3. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm bars. The beam is simply supported over a span of 6 m and carries a uniform dead load of 0. 680 KN/m including its own weight. Use fy=276.50 MPa and fc-20.70 MPa. In checking whether steel yields or not, the value of "fs" is__ _MPa. 1644.056 1302.491 1935.087 2402.455 O2735.802 O 3014.642 Other:
A wooden beam is fabricated by nailing together three pieces of dimension lumber as shown. The cross-sectional dimensions of the beam are also shown. The centroid is 3.4 in. below the top surface of the beam, and the moment of inertia about the z axis is 230.9 in.4. The beam must support an internal shear force of V = 365 Ib. If each nail can provide 120 Ib of horizontal resistance, determine the maximum spacing sfor the nails. 2 in. 4 in. 2 in. 2 in. 8 in. O 4.86 in. 8.32 in. O 7.91 in. 9.36 in. O 5.59 in.
The composite beam shown in the figure is simply supported and carries a total uniform load of 50 kN/m on a span of 4.0 m. The bearn is built of a wood member having cross sectional dimensions 150 mm x 250 mm and two steel plates of cross-sectional dimensions 150 mm x 50 mm. Determine the maximum stresses, in the steel and wood, respectively. If the moduli of elasticity are E {s} = 209GPA and E {w} = 11GPA (Disregard the weight of the beam) Steel 50 mm 50 kN/m Wood B Steel 50 mm 4.0 m- 150 mm 250 mm
Solve it ASAP
PLEASE DRAW THE FBD. DO NOT COPY YOUR ANSWER FROM OTHER. I WANT TO SEE THE FBD OF INDIVIDUAL DEFORMATIONS ON HOW YOU WILL ARRIVE ON YOUR ANSWER. DRAW FBD ON EACH PLEASE. NOT ONLY ONE FBD