The composite beam shown in the figure is simply supported and carries a total uniform load of 50 kN/m on a span of 4.0 m. The bearn is built of a wood member having cross sectional dimensions 150 mm x 250 mm and two steel plates of cross-sectional dimensions 150 mm x 50 mm. Determine the maximum stresses, in the steel and wood, respectively. If the moduli of elasticity are E {s} = 209GPA and E {w} = 11GPa (Disregard the weight of the beam) Steel 50 mm 50 kN/m Wood Steet 50 mm 4.0 m 150 mm 250 mm

The composite beam shown in the figure is simply supported and carries a total uniform load of 50 kN/m on a span of 4.0 m. The bearn is built of a wood member having cross sectional dimensions 150 mm x 250 mm and two steel plates of cross-sectional dimensions 150 mm x 50 mm. Determine the maximum stresses, in the steel and wood, respectively. If the moduli of elasticity are E {s} = 209GPA and E {w} = 11GPa (Disregard the weight of the beam) Steel 50 mm 50 kN/m Wood Steet 50 mm 4.0 m 150 mm 250 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 22 A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4 m and have a web width of 250 mm, an effective depth of 400 mm and overall depth of 500 mm. The tensile reinforcement consists of 6-ϕ32 mm bars in two rows. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the ultimate bending moment strength of the T-beam in kN·m.
Only compute the I, where the formula is; I=bh² / 12
How to solve for the centroid of the composite body using the principle of moments and treat each part as a finite element of the whole figure (show a step by step solution)
Compute the maximum force F (in KN) that can be applied to the composite rod if the allowable total deformation of the composite rod is limited to 0.80 mm A 6F B Steel Rod d = 100 mm L=3m E = 200 GPa C Aluminum Rod d = 70 mm L = 2m E = 70 GPa 3F D Bronze Rod d = 40 mm L = 4 m E = 80 GPa 2F
A simply supported wood beam, reinforced with steel plates, has the cross section shown. The beam carries a uniformly distributed load of 16 kN/m over the middle half of its 4-m span. If modular ratio is equal to 15, determine the largest bending stresses in the wood and steel. 96 mm 96 mm -200 mm 8 mm 240 mn 8 mm
Please answer the question correctly and pleaase put the answer on the paper. Thank you Note: The tolerance is ± 1 in the third significant digit. Put the exact answer
Question # 1: The composite beam is made of steel (4) bonded to brass (B) and has the cross section shown. If the allowable bending stress for the steel is (sallow) st = 180 MPa, and for the brass (sallow) br = 60 MPa, determine the maximum moment (M) that can be applied to the beam Ebr 100 GPa, Est= 200 GPa B Question # 2: Determine the maximum shear stress acting at section a-a in the beam. 150 N/m m 8000 N Bla 1.5 m 1.5 m 50 mm 50 mm 200 mm 175 mm 200 mm -B 400 mm 75 mm 600 mm 75mm
i need the answer quickly
A reinforced concrete beam is shown in the figure below. 0.75-in, diameter rods Wo 20 in. 2.5 in. 8 ft- 8 ft 10 in. Part A Determine the maximum uniform distributed load wn that can be supported by the reinforced concrete beam if the allowable tensile stress for the steel is (Ost )allow = 30 ksi and the allowable compressive stress for the concrete is (oconc )allow = 3 ksi . Assume the concrete cannot support a tensile stress. Take Est = 29(10) ksi , Econe = 3.6(103) ksi Express your answer to three significant figures.
!