A composite beam is constructed using a steel plate (14 mm x 155 mm) with two wood beams (75 mm x 155 mm) on either side. The wood and steel are securely fastened to act as a single beam. The beam is subjected to a positive bending moment M₂ = 6.50 kN. m. Steel Wood Calculate the maximum tensile and compressive stresses in the wood and steel if E= 11 GPa and E= 200 GPa. (Enter your answers in MPa. Use the deformation sign convention. Use the general theory for composite beams described in the textbook.) maximum tensile stress in wood MPa maximum tensile stress in steel MPa maximum compressive stress in wood MPa maximum compressive stress in steel MPa

A composite beam is constructed using a steel plate (14 mm x 155 mm) with two wood beams (75 mm x 155 mm) on either side. The wood and steel are securely fastened to act as a single beam. The beam is subjected to a positive bending moment M₂ = 6.50 kN. m. Steel Wood Calculate the maximum tensile and compressive stresses in the wood and steel if E= 11 GPa and E= 200 GPa. (Enter your answers in MPa. Use the deformation sign convention. Use the general theory for composite beams described in the textbook.) maximum tensile stress in wood MPa maximum tensile stress in steel MPa maximum compressive stress in wood MPa maximum compressive stress in steel MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A storage tank of air, 30 inches in diameter, is to withstand an internal pressure of 180 psi with a design factor of 3.5 based on ultimate stress. The steel has the strength equivalent of C1020 annealed and the welded joints should have a relative strength of 92%. Note: ultimate stress of for annealed C1020 steel is 50 ksi. Compute for longitudinal stress of the tank. a.13, 171 psi b.13, 786 psi c.12,893 psi d.12,860 psi
Please just do problem 8.2
SITUATION 1. A composite bar is made by attaching a copper rod of length 900 mm and diameter 30 mm and a brass rod of length 600 mm and diameter 45 mm as shown. A load of 20 kN is applied at 20°C. For copper, E = 120 GPa and a = 18 x 10-6/°C. For brass, E = 90 GPa and a = 20 x 10-6/°C. The temperature rises to 50°C. Copper 44.95 MPa 63.29 MPa 72.84 MPa 900 mm 40.70 MPa + What is the stress in the copper rod if the supports are unyielding? Brass - 20 kN 600 mm
i need the answer quickly
Two wood boards, each 16 mm thick, are joined by the glued finger joint shown. The finger joint will fail when the average shear stress in the glue reaches 760 kPa. Determine the shortest allowable length d of the cuts if the joint is to withstand an axial load of P = 7.0 kN. Use a = 18 mm and b = 144 mm. d Glue a P P a Answer: d= i b mm
View Policies Current Attempt in Progress A composite beam is made of two brass [E-94 GPa] plates bonded to an aluminum [E-70 GPa] bar, as shown. The beam is subjected to a bending moment of 1850 N-m acting about the z axis. Assume b-57 mm, d₁-43 mm, d₂-9 mm. Determine: (a) the maximum bending stresses Obr. Gal in the brass plates and the aluminum bar. (b) the stress in the brass brj at the joints where the two materials are bonded together. 2 Brass (2) Aluminum (1) Brass (2) Answers: (a) abr = (b) Obrj = i i b MPa, Gal = i MPa. MPa.
The composite bar is initially stress-free. Calculate the stress in each material and indicate tension or compression if the temperature has increased to 25°C. Consider that the walls are unyielding and suitably braced to prevent buckling. Use 2 decimal places.
The working stresses for the manufactured wood beam are 10 MPa in bending and 1.4 MPa in shear. Determine the largest allowable value of the load intensity co. 25 mm Wo 25 mm -3 m 6 m- 200 mm 1 250 mm 25 mm
1. Three metal strips, each 40 mm height, are bonded together to form the composite beam shown. The modulus of elasticity is 210 GPa for the steel, 105 GPa for the brass, and 70 GPa for the aluminium. If the allowable bending stress for the aluminum (Gallow)al= 100 MPa, for the steel (Gallow)s=150 MPa and (Gallow)b= 200 MPa for brass determine the maximum allowable intensit of w of the uniform distributed load. 2w Aluminum 2w 10 mm Brass 10 mm Steel 20 mm 2m - 40 mm
The structural efficiency in managing bending, shear and for steel vs concrete
Please answer it clearly don't waste my question I will vote it up for your effort thank you in advance.
fc = 25 mpa, fy = 414 the tensile stress is in the concrete is?