Figure 1 shows a simply supported beam with a concentrated force P applied at the mid-span,B. Given the modulus of elasticity is E = 210GPa. To reduce the displacement of the system, avertical spring with spring constant ks is installed at B as shown in the figure.P1 mI= 2.5 x 10-4 m4B1 mFigure 1Ck = 2 × 108 N/m7IIIIT a)Without considering the vertical spring, determine the stiffness coefficient of the simplysupported beam with both the force and displacement are vertically downward at B.

Answered: Image /qna-images/answer/31ab9545-c14f-40aa-8a82-943dced415b3.jpg

Answered: a) Without considering the vertical…

a) Without considering the vertical spring, determine the stiffness coefficient of the simply r== ===- -។ ។។។ ។'''' => ។ F 490009901991 pacmaMOp on

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the stepped bar made with a linear elastic material and subjected to an axial load of1 kN, as shown in the figure. 4000 L1-400 mm + L2- 900 mm 1 1 41-100 mm² EI=2×10 MPa 42=60 mm² E2-3x105 MPa P-1 kN Segments 1 and 2 have cross-sectional are of 100mm² and 60mm², Young's modulus of 2x10³ MPa and 3×10³ MPa, and length of 400mm and 900mm, respectively. The strain energy (in N-mm, up to one decimal place) in the bar due to the axial load is
B1 The beam shown in Figure B1 is made of aluminium alloy with a Young's modulus of 70GPa. The cross section is rectangular with a width of 5mm and depth of 20mm. The beam is simply supported over a span length (L) of 550mm and loaded with a point load of 5kN at a distance 55mm from the left hand end. 55 mm 5 KN L=550 mm Figure B1 (a) Calculate the support forces and determine an expression for determining the bending moment at every point in the beam. (b) Derive an expression to calculate the deflection of the beam at any point between the two supports. (c) Calculate the location of maximum deflection and the value of maximum deflection itself.
02 A cast-iron beam has a section as shown in the figure below. The beam is subjected to two concentrated loads of 3kN. The N.A is located at 35 mm from the bottom and that maximum flexural tensile stress =20 MPa. Determine the width (X) of the flange. 20mm 3kN 3kN 120mm 15m 35mm 20mm 2m 3m 2m
A cantilever of length L has a solid circular cross section of diameter D and carries a vertically downward load Wat its free end. The modulus of rigidity of the cantilever is G. Calculate the shear stress distribution across a section of the cantilever and hence determine the deflection due to shear at its free end. Ans. t = 16 W(1–4y²ID²)/3¤D², 40WL/9#GD² (downwards).
An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B2 =D 1.0 m; B;= 0.6 m. Determine the axial load acting on bar B, in kN. 35KN B1 B2 B3 10KN 15KN 30KN A 35 B) 20 C) 10 (D) 5
The rigid beam shown in the Figure is fixed at the top by two posts (dext = 40mm), one in AISI 4340 steel and the other in 6063-T6 aluminum. The posts are 500 mm long when no load is applied to the beam. Calculate the longitudinal displacements (δAl , and δFe) and the half stresses (σAl , and σ Fe) in the posts. Determine the angle of inclination of the beam (in degrees) when a homogeneously distributed load of 400 kN/m is applied. Calculate the factors of safety. Use E Fe = 200 GPa , and Eal = 70 GPa. Elastic limit AISI 4340 (Sy = 786 MPa), and AA6063-T6 (Sy = 214 MPa) (answers:/ δAl = -1.14 mm ; δFe = -0.40 mm σAl = -159 Mpa ; σFe = -159 Mpa ; angle ≈ 0.04° FSAL = 1.3 FSFE = 4.9)
The wide-flange pinned-end column shown in the figure carries two loads, a force acting at the centroid P₁ = 450kN and a force P₂ = 270kN acting at distance s = 100 mm, from the centroid. The column is an HE 240B shape with L = 4.2m, E = 200 GPa, and Oy = 290 MPa. (a) What is the maximum compressive stress in the column?
Q2: The simply supported beam shown as Figure 5. below is subjected to Loading as shown on the Figure. Using singularity function method. Find the maximum Lenght (L) so that the max. deflection is not greater than 30mm for the Beam.. The flexural rigidity (El) of Beam section El = 50*103 KN.m?2 “4m L Sm
9. A steel portal frame has dimensions, plastic moment capacities and applied loads as shown in the figure. The vertical load is always twice of the horizontal load. The collapse load P required for the development of a beam mechanism is P B A Mp K+ 2P 2Mp L с Mp D L
ASAP
Consider the stepped bar made with a linear elastic material and subjected to an axial load of1 kN, as shown in the figure. L1-400 mm + L2- 900 mm 1 2 41-100 mm² EI = 2x10³ MPa 42 = 60 mm² E2-3x105 MPa P-1 kN Segments 1 and 2 have cross-sectional are of 100mm² and 60mm², Young's modulus of 2×10³ MPa and 3×10 MPa, and length of 400mm and 900mm, respectively. The strain energy (in N-mm, up to one decimal place) in the bar due to the axial load is
The beam shown in the figure below is subject to a moment of M = 17 kN.m as illustrated. Calculate the maximum tensile and compressive bending stresses. |-75 mm - - 12 mm B 12 mm 12 mm 75 mm 250 mm D 12 mm