A wire 60.0 cm long is held parallel to and 100 cm above a long wire carrying 100 A and resting on the floor. The 60.0-cm wire is released and falls, remaining parallel with the current-carrying wire as it falls. What is the induced emf on the wire 0.400 s after the wire is released? Give your answer in µV. (g=10 m/s² ) Başlangıçta, 60.0 cm uzunluğunda bir tel, yerde duran çok uzun 100 A akım taşıyan bir tele paralel 100 cm yüksekte durmaktadır. 60,0-cm uzunluğundaki tel serbest bırakılmış ve yerdeki akım taşıyan tele paralel kalacak şekilde g ivmesi ile serbest düşmektedir. Kısa tel serbest bırakıldıktan 0,400 s sonra üzerinde indüklenen emk µV cinsinden nedir? (g=10 m/s? )

A wire 60.0 cm long is held parallel to and 100 cm above a long wire carrying 100 A and resting on the floor. The 60.0-cm wire is released and falls, remaining parallel with the current-carrying wire as it falls. What is the induced emf on the wire 0.400 s after the wire is released? Give your answer in µV. (g=10 m/s² ) Başlangıçta, 60.0 cm uzunluğunda bir tel, yerde duran çok uzun 100 A akım taşıyan bir tele paralel 100 cm yüksekte durmaktadır. 60,0-cm uzunluğundaki tel serbest bırakılmış ve yerdeki akım taşıyan tele paralel kalacak şekilde g ivmesi ile serbest düşmektedir. Kısa tel serbest bırakıldıktan 0,400 s sonra üzerinde indüklenen emk µV cinsinden nedir? (g=10 m/s? )

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q#02. What do you infer from the following graph drawn from data based upon Measurement of Charge-to-Mass (e/m) Ratio for the Electron by Helmholtz coil experiment? Discuss the salient features of Helmholtz coils 1.00 0.99 0.98 0.97 0.96 0.95 -0.4 -0.2 0.0 0.2 0.4 Relative distance from the center of the coils x/a Relative magnetic field B/B,
#3
I need the answer as soon as possible
Q₁ +25.0 nC is at the origin. Q₂= -15.0 nC is at x = 1.00 cm. Q3 +30.0 nC is at x=-1.00cm. A. Find the total Voltage at x₂-3.00 cm created by these three charges B. Find the total Voltage at x 4.00 cm created by these three charges C. What is the change in potential energy of a proton that moves from x₂ to xb?
9. Write an equation to obtain the potential difference at point a with respect to point b, Vab? 10. What is the potential difference at point a with respect to point b, Vab?
draw graphs of the voltage over r1 (v against t graph) for the charge cycle. starting at t=0 until steady state after the switch is closed (initially all capacitors are empty) and another case when the switch is opened (initially the capacitors are fully charged)r1 = 100k ohms r2 = 10k ohms v1 = 5v (dc) c1 = 100nf c2 = 220nf c3 = 330nf
plz Answer this Quis. asap!!
None
Q. 26. A specimen is tested for insulation resistance by the loss of charge method. The specimen capacitance is 2.8 nF. It is observed that after charging the voltage falls from 260 V to 160 V in one minute. If the voltmeter used is assumed with infinite resistance, determine the insulator resistance. A. 44.14 GO B. 17.38 GO C. 36.38 GO D. 9.38 GO
44% P 8:02 * ZAIN IQ I. med1.pdf 1. A given material has a resistance of 20 2 at room temperature (20°C) and 25 2 at a temperature of 85°C. a) Does the material have a positive or a negative temperature coefficient? Explain briefly. b) Determine the value of the temperature coefficient, a, at 20°C. c) Assuming the resistance versus temperature function to be linear, determine the expected resistance of the material at 0°C (the freezing point of water) and at 100°C (the boiling point of water). 2. Find the equivalent resistance Rab in the circuits of Figure below. a o 102 60 Ω 30 Ω bo ww ww 20 Ω 3. The network of Figure below is the basic biasing arrangement for the field-effect transistor (FET), a device of increasing importance in electronic design. (Biasing simply means the application of de levels to establish a particular set of operating conditions.) Even though you may be unfamiliar with the FET, you can perform the following analysis using only the basic laws introduced in your…