A wire 4m long is stretched horizontally between points A and B 4m apart. A load W placed at the center of the wire produces a sag of 53.4mm, a. If the wire is 25mm2 in cross-section and the Young’s modulus is 200GPa, what is the magnitude of load W? b. If the load was reduced by 40%, what will be the sag?

Q: cylindrical rod subjected to an uniaxial tensile load P as shown, given P = 800 (N), the original…

A: The cylindrical rod with 8 mm diameter and 60 mm length is subjected to an uniaxial tensile load of…

Q: A mechanism used in printing machinery consists of a helical spring which is having a wire diameter…

A:

Q: Examine the rod below. It is fixed into a wall at the left hand end. From the wall to point B is…

A: Given: The force at D, P = 221.6 N The force at D along y-axis, Fy = 400 N The force at D along…

Q: A mechanism used in printing machinery consists of a helical spring which is having a wire diameter…

A: Given data wire diameter (d) = 5 mm  OD of coil = 60 mm active coil = 12 Permissible shear stress =…

Q: Question 3: a. A mass of (Z + 50) kg is hung on a steel wire of diameter (Z + 5) mm and the…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: A steel bar is 900 mm long: its two ends are 40 mm and 30 mm in diameter and the length of each rod…

A:

Q: 6) A steel rod with a cross-sectional area of 0.25 in? is stretched between two fixed points. The…

A:

Q: A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and…

A:

Q: 6. Three wires are used to support the 150-lb force. The wires AB and AC are made of steel, and wire…

A: Tension occurred in a cable due to stretch or pulled It is an internal force that acts all along the…

Q: w 12mm dia SK 18mm dia. P=12 kN HAD 12mm dia 2 m. 2. Three steel cable jointly support a load of…

A:

Q: ny mm is the smallest allowable outer diameter of the washer

A: GIVEN :- Diameter of rod : d= 34mm washer inner diameter : di  = 37.5 Allowable stress of rod : σ=…

Q: area of the rod is 1200 mm a=11.7u m/(m.'C) and E=200 GPa. Solve assuming (a) that the wall is rigid…

A:

Q: A straight bar of uniform cross sectionis tested in tension. The bar's cross sectional is 6.5 square…

A:

Q: we want to build a single-rail overhead crane in the workshop.when the load reaches the extreme…

A: Given: The extreme location of load, x = 1800 mm = 1.8 m The tensile stress in rope, σ = 600 MPa The…

Q: Q1. Links BC and De are made of the same material (E = 29x106 psi) %3D and have the same cross…

A: The free-body diagram of the figure is given below:  Taking moment about point F :…

Q: 1. A uniform bar, 9 ft long weighs 5 Ibs. Is supported from left end by a 12 Ibs load. Find W R = A…

A:

Q: 1. A frame is shown to the right. The link BC is t = 6mm thick (into the page) and has width, w…

A:

Q: You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m).  The…

A:

Q: °C) .what is the length of the bar in a summer day when the temperature is (38 C) ?Calculate the…

A: Given: T1= -20oC T2=38oC L=50 m α=12×10-6 C-1 To determine: The length of the bar in the summer day…

Q: A steel bar with the dimensions and cross section shown is suspended vertically. Three concentric…

A: The change in length due to 22250 N force is ∆L1=PLAE=22250×1+0.65+0.356.5×10-4×210×109=3.26×10-4 m…

Q: A vinyl [E = 2.85 GPa; v = 0.41] block with width b = 50 mm, depth d = 100 mm, and height h = 270 mm…

A: Young's modulus= 2.85GPaPoisson's ratio= 0.41Load applied = 100kN Find the change in depth

Q: 4 The rectangular block of material of length L and cross-sectional area A fits Snugly between two…

A: The internal resisting force applied by the object when an external force is applied on the object…

Q: A mechanism used in printing machinery consists of a helical spring which is having a wire diameter…

A:

Q: Two steel pipes are used to support a 50KN load, as shown below. The pipes are connected to the wall…

A: Draw the FBD and find supports reactions

Q: A helical spring used in an automobile suspension is having a wire diameter of 6mm and an outside…

A:

Q: Question Two A steel flat of thickness 10 mm tapers uniformly from 60 mm at one end to 40 mm at…

A: To find :  The percentage error  Given :  The thickness of steel flat plate is t=10 mm. The taper…

Q: A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and…

A:

Q: 3. Consider a frame as shown below. The vertical section AB is 3 m long, and the horizontal section…

A: Note: Complete solution will be provided soon Given data: Frame has hollow circular section frame…

Q: A helical spring used in an automobile suspension is having a wire diameter of 7mm and an outside…

A:

Q: A horizontal bar, fixed at one end (x = 0), has a length of 1 m. and cross-sectional area of 100 mm2…

A:

Q: A bar, 12 mm in diameter is acted upon by an axial load of 20 kN. The change in diameter is measured…

A: The Young's modulus is nothing but the slope of the stress-strain curve of the material under…

Q: 5. A strain gauge is used to weigh an object that is mounted on a copper column of 6-in diameter. If…

A:

Q: A steel wire is 10m long supports a tensile load of 2000N. What is the diameter if the stress is 140…

A:

Q: 2. The tank shown in the figure is fabricated from 10mm steel plate. Determine the maximum…

A: As per our guidelines we are supposed to answer only one question. Kindly repost other questions as…

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.