Solve it correctly please. Known values:ySpeed of Winding up Cable15 ft 8.6 ftft4Problem Statement:A winch motor M winds up a cable at a constant rate, causing a crate to slide along the floor. Determine:The speed of the crate in the position pictured:The acceleration (magnitude) of the crate in the position pictured:Is the crate speeding up or slowing down at this instant?-select-Be sure to include units with your answers.

Given data as per question speed of winding =4 ft/s Calculations…

Answered: A winch motor M winds up a cable at a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Imagine two ordinary gears of different diameters meshed together, with the larger being the driver. If the larger gear has 108 teeth around its circumference and rotates at 5.80 rad/s, the smaller gear, which has only 20 teeth, will rotate at what speed?
calculate the indexing for the following: 1. 914 divisions 2.1300 divisions note: the link for the calculations is provided https://www.youtube.com/watch?v=Z0FR4gzPHiU
Topic:Gear calculation Answer the following table. Answer only no. 6-8 Write legibly.
The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and driver gears are 84cm and 35cm respectively. If driven shaft runs with 10 r.p.s,determine the following; 1. Center distance between the two shafts in mm. 2. Speed of driver shaft in rpm 3. Velocity ratio 4. Number of teeth's on driver and driven shaft for the given module 6mm
I need the answer quickly
Answer the attached file
A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth. The gear transmits 40 hp and rotates at 450 rpm with a normal pressure angle of 20 degrees. What is the value of the circular pitch in mm per tooth?
In a taper turning operation 35 is the diameter of the large end in mm, 25 is the taper angle in ° and 24 is the length of taper in mm. Find the diameter (d) of the small end in mm Diameter (d) of the small end in mm
Consider the gear train below where Gear D has 80 teeth and Gear A is spinning with 600 rpm. D 60 teeth the A 40 teeth 20 teeth a. What is the speed of Gear D? We want to adjust the gear train. We can only change out Gear C for a different sized gear. Gear A will continue spinning with 600 does our new Gear C need to have so that Gear D b. How many teeth rpm. spins with 200 rpm? B.
Two shafts, each carrying a four-stepped pulley, are to be connected by a crossed belt. The driving shaft is to turn 150 rpm while the driven shafts is to turn 50, 150, 250 and 600 rpm. The smallest step of the driver is 10 in. in diameter. Find the diameters of all steps. Please Show a clear and detailed solution (with illustration). Thank you!
B 96. Consider the gear train shown in the given figure and table of gears and their number of teeth. F E + +, + + Gear :A B C DE F No of teeth:20 50 25 75 26 65 A с D Gears BC and DE are moulded on parallel shaft rotating together. If the speed of A is 975 r.p.m., the speed of F will be
Two mating 12-pitch gears have 18 external and 48 internal teeth, respectively. Determine the following: Their pitch diameters. • The center distance.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A winch motor M winds up a cable at a constant rate, causing a crate to slide along the floor. Determine: The speed of the crate in the position pictured: The acceleration (magnitude) of the crate in the position pictured: