A) What is the indeterminacy degree of the shown truss?B) Determine the stiffness matrix for N1-N2, N1-N3, N2-N3 (We have already obtained-pleasecheck the slides), N3-N4, N2-N4.Additional tasks to add 3to your final exam.C) Find the stiffness matrix for the entire truss using the assembly.D) Find the displacements and reactions.6'N360 kip2 in?N48'N1N22 in?80 kip2 in?1.5 in?2 in?

Here we have the stiffness matrix as shown below k=AEL C2CS-C2CSS2-CS-C2-CSC2-CS-S2CSThe stifness is…

A) What is the indeterminacy degree of the shown truss? B) Determine the stiffness matrix for N1-N2, N1-N3, N2-N3 (We have already obtained-ple check the slides), N3-N4, N2-N4. ditional tasks to add 3 to your final exam. C) Find the stiffness matrix for the entire truss using the assembly. D) Find the displacements and reactions. 6' N3 60 kip 2 in? N4 8' N1 N2 2 in? 80 kip 2 in? 1.5 in? 2 in?

A) What is the indeterminacy degree of the shown truss? B) Determine the stiffness matrix for N1-N2, N1-N3, N2-N3 (We have already obtained-ple check the slides), N3-N4, N2-N4. ditional tasks to add 3 to your final exam. C) Find the stiffness matrix for the entire truss using the assembly. D) Find the displacements and reactions. 6' N3 60 kip 2 in? N4 8' N1 N2 2 in? 80 kip 2 in? 1.5 in? 2 in?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Equation of Motion The triangle is made of 3 rods of a length 1-2.1ft and density is p = 4 lb/ft. ^ 1) Establish what you think is the best Coordinate system for this problem and explain why. 2) Find the location of the center of gravity (x bar and y bar). 3) Find the weight of the triangle. 4) Find the Mass Moment of Inertia at O of the triangle. 5) Draw the FBD and kinetic diagram of the triangle. 6) Find the accelerations of the triangle (angular and linear). 7) Find the Pin Reaction at O: . On and Ot • or Ox and Oy . • Magnitude O, and direction. In the box below, enter the angular acceleration & in rad/s with one decimal. Include the sign + if CCW or - sign if CW.
topic: X-Y Coordinates & N-T Coordinates X-Y Coordinates & N-T Coordinates I need the answer ASAP please thank you.
1) A low-friction cart is placed between two identical springs attached to rigid walls. If you push the cart against one of the springs and release it, it will continue to move back and forth between the springs. www Draw a force-time graph showing the sum of the horizontal forces exerted on the cart as it moves back and force between the springs. Scientific Abilities Is able to construct a force diagram Missing No representation is constructed. Inadequate FD is constructed but contains major errors such as incorrect mislabeled or not labeled force vectors, length of vectors, wrong direction, extra incorrect vectors are added, or vectors are missing. Needs Improvement FD contains no errors in vectors but lacks a key feature such as labels of forces with two subscripts or vectors are not drawn from single point, or axes are missing. Adequate The diagram contains no errors and each force is labeled so that it is clearly understood what each force represents. Explain whether or not this…
Need help on all questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
Physics In a simple supported beam , write the moment equation of the beam shown in this video if it is loaded with 10 kN/m uniformly distributed over the entire simple span of 4 meters and a concentrated load of 20 kN applied 2 meters from the left support. Present your answer using the GAPSA form by indicating all the given data, what is being asked in the problem, the appropriate formula, the entire solutions / calculations and the answer accompanied with corresponding unit of measurement. Thank you.calculate the moment equation and the segment ,using double integration method
The kinematic diagram is given as ?12 = 600 and the speed of the mechanism is constant and ?'-12 = 50 rad/second in the slide mechanism, the limb dimensions of which are given below. Find the following items. a) Write the vector closure equations. b) Put the vector closure equations in scalar form. c)Find ?13, ?14. d)Find s'13, ?14. e)Find s'', ?14.
Bonus Question: 8 Extra points A block of mass m = 1.0 kg is dropped from height h= 75cm onto a spring. The mass will attache to the spring and then the spring will compress. a). Find the spring constant if the maximum distance the spring is compressed is 10cm in following arrangement? ០០០០០០០០០ b). Find the maximum distance the spring is compressed in following arrangement if the angle is 30 degrees? You are using same spring. ss. mmmm 8
Q5
Needs Complete solution with 100 % accuracy. Don't use chat gpt or ai i definitely upvote you be careful Downvote for ai or chat gpt answer.
Can anyone help me with this question
Hi, I have an engineering dynamics question.
Dynamics of Rigid Bodies Please help ASAP. Rate will be given accordingly. Please write your answer on paper. Thank you so much. Note: The tolerance is ±1 in the third significant digit.