M h B For the given system; a) Draw bending moment and shear force diagrams. b) Determine the most critical section. c) Show the stress distribution on this critical section. d) If allowable stresses for tension and compression are 7000 N/cm² and 12000 N/cm², respectively, determine the safety of the structure. GIVEN: {1= 80 cm, {2=40 cm, qo = 60 N/cm F= 500 N, b = 5 cm, h = 4 cm, t = 0.5 cm %3D

M h B For the given system; a) Draw bending moment and shear force diagrams. b) Determine the most critical section. c) Show the stress distribution on this critical section. d) If allowable stresses for tension and compression are 7000 N/cm² and 12000 N/cm², respectively, determine the safety of the structure. GIVEN: {1= 80 cm, {2=40 cm, qo = 60 N/cm F= 500 N, b = 5 cm, h = 4 cm, t = 0.5 cm %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The stresses on the surface of a hard bronze component are shown in the figure below. The yield strength of the bronze is σY = 345 MPa.a) What is the factor of safety predicted by the maximum-shear-stress theory of failure for the stress state shown? Does the component fail according to this theory?b) What is the value of the Mises equivalent stress for the given state of plane stress?c) What is the factor of safety predicted by the failure criterion of the maximum-distortion energy theory of failure? Does the component fail according to this theory?
- once answered Correctly will UPVOTE!!
As shown in Fig. 4, a steel frame with Young's modulus E=203 GPa and Poisson's ratio v-0.3 is subjected to the moment M. a) Calculate the ratio of Gmin |/ |Omax). b) Sketch the normal stress in the steel frame. M 5cm 5 cm 25 cm M Fig. 4
Using mohr’s circle
H
Asap
M A For the given system; a) Draw internal force diagrams and determine the most critical section. b) Show the stress distribution on this critical section and find the maximum normal stress. GIVEN: €1 = 80 cm, {z=40 cm, M= 8000 Nem, b= 4 cm, h = 6 cm, t= 1 cm F = 1400 N, q.= 30 N/cm
For the beam shown in Figure below and values provided below, neatly draw the Shear Force and Bending Moment diagrams, then complete the values in the question as required. Provide answers rounded off to the next whole number - do not include units with your answers. P1=80kN P2=80kN RA=116kN RD=134kN
AL: 1₂ The above figure (not drawn to scale) shows a rod made up of two cylindrical sections of the same material. The left cylinder has diameter d, = 30mm and length 4 = 150mm. The right cylinder has diameter dy=10mm and length = 150mm. The rod is subjected to a force F = 50KN. Find the total extension in the rod, AL, given that E = 203kN/mm². Enter your answer in mm to 5 decimal places in the box below: mm -F
Find all the non-zero components of internal reaction forces in section a-a. If you select wrong answers, you will have negative score in this question. 200 mm 200mm D 400 N 800 N
The specification of a cylindrical vessel are as follows: D = 350 mm %3D t = 12 mm P = 4.5 MPa Determine the a) Longitudinal Stress; b) Transverse Stress ; and c) new diameter and wall thickness if the 550-mm length cylindrical vessel is replaced by a spherical vessel of the same volume and equal material strength.
need help, answer is not 50 or -50 either