A well-mixed cement-lined storage tank contains water initially at 50°C. The water loses energy to its surroundings via conduction through the tank's concrete-lined walls. The tank sits in an unheated warehouse with an air temperature of 0°C. A diagram of the storage tank is shown below. The cement lining is 1.5-cm thick and has a thermal conductivity (htc) of 2.0 W/(m K). height = 1.5 m diameter = 2.0 m a. How long will it take (in minutes) for the water to cool to 40°C?

A well-mixed cement-lined storage tank contains water initially at 50°C. The water loses energy to its surroundings via conduction through the tank's concrete-lined walls. The tank sits in an unheated warehouse with an air temperature of 0°C. A diagram of the storage tank is shown below. The cement lining is 1.5-cm thick and has a thermal conductivity (htc) of 2.0 W/(m K). height = 1.5 m diameter = 2.0 m a. How long will it take (in minutes) for the water to cool to 40°C?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider steady-state conditions for one-dimensional conduction in a plane wall having a thermal conductivity k = 40 W/m-K and a thickness L = 0.3 m, with no internal heat generation. -T2 L Determine the heat flux, in kW/m², and the unknown quantity for each case. Case T1(°C) T2(°C) dT/dx(K/m) q (kW/m?) 1 50 -20 i i 2 -30 -10 i i 3 70 i 160 i 4 i 40 -80 i 5 i 30 200 i
answer quickly
3.4 Estimate the rate of heat loss due to radiation from a covered pot of water at 95 ° C. How does this compare with the 60 W that is lost due only to convection and conduction losses? What amount of energy input would be needed to maintain the water at its boiling point for 30 minutes? The polished stainless steel pot is cylindrical, 20 cm in diameter and 14 cm high, with a tight-fitting flat cover. The air temperature in the kitchen is about 25 ° C. State any assumptions you make in deriving your estimates
A furnace wall consists of 2 ft of brick . The brick has athermal conductivity of 0.6 Btu/ hr sq ft ( ° F /ft), a specific heat of0.2 Btu/ lb ° F, and a density of 110 lb/cu ft. The temperature atthe inside surface of the wall is 1100 ° F , and at the outside surface,200 ° F .(a) Calculate the thermal diffusivity of the brick .(b) Calculate the heat loss per hour through a wall 10 ft high and10 ft long(c ) Calculate
3 Brass cube "p = 8530 kg/m , c= side length =9 mm, are annealed by heating them first to 813°C in a furnace and then allowing them to cool slowly to 130°C in ambient air at 28°C. If the average heat transfer coefficient is 19.9 W/m .°C, If 2204 balls are to be annealed per hour, what is the total rate of heat transfer (watts) from the balls to the ambient air? 380 J/kg.°C, k = 110 W/m.°C, a = 33.9E-6 W/m.°C",
1) A wall section composed from the outside to inside, of concrete brick 100mm thick, an air space of 50mm, two layers of fiberglass insulation 38mm thick, concrete block 150mm thick and air space of 19mm and a gypsum board of 13mm. The exterior conditions are -20C and RH=90% while the interior conditions are 23C and RH=40%. The surface temperature from the outside to inside are shown in the figure. The permeances are: Still Air: µ = 175 ng/pa.s.m Fiber glass: M=2560 ng/pa.s.m? Concrete block: M= 200 ng/pa.s.m? Gypsum board: M= 2000 ng/pa.s.m? Concrete brick: µ = 4.55 ng/pa.s.m Determine if there is a risk of condensation, and if there is, what is the condensation rate? What would happen if a vapor barrier (M=0.2 ng/pa.s.m²) was installed on the warm side of the insulation (Surface 4). 21с 19C 16 С 12C -10 -15C -18C -19C Gyp Air Concrete Fiber Fiber Air Concrete Outdoor Indoor sum block Glass Glass brick 230 19 50 mm -20C 13 150 mm 38 mm | 38 mm 100 mm RH=90% RH=40% mm mm Surf. 1 Surf.…
The convection coefficient for a hot a fluid flowing over a cool surface is 150 W/m^2. The fluid temperature is 410 K and the surface is held at 290 K. Determine the heat transfer per unit surface area from the fluid to the surface.
Find the temperature profile of the rectangular plate 4m x 4m, whose temperature at the side are given below: Take delx= del y= 1 m. 100 C 75 C OC 50 C
A house has a three meter deep basement (foundation) wall that is in a 10 meter by eight meter rectangular shape based on interior dimensions. On average, 2.5 meters of the wall is below grade. Assume the outside air temperature is 38°C and the inside temperature is 20°C; there is an average ground temperature of 27°C. Determine the rate of heat loss through the wall if it is insulated with an R-value of about 30°C.m^2/W.
In a lab testing material samples to determine the thermal conductivity of the material. Now, the test specimens are 18.5 cm long by 14.4 cm wide and 0.26 cm thick. The sample is placed in a test device so that one of the large sides is maintained at 13, while the other large side is kept at -7. The heat transfer through the sample is measured to be 287 Watts. Determine the thermal conductivity. Give your answer to 2 decimal places.
The initial temperature of a 50 cm long silver wire is 50 °C. The circumference of the wire in question is completely insulated, but both ends are kept at a temperature of 0 °C (zero degrees Celsius). Obtain the heat conduction along the wire as a function of time and position and, taking a single term in the solution, determine how many degrees Celsius the temperature in the middle of the rod will be after 7 minutes. (For silver wire, α=1.70 cm2/s.)