3) The two sides of a large plan wall are maintained at constant temperatures of T₁ = 120°C and T₂ = 50°C, respectively. If you know that the wall thickness L = 0.2 m, thermal conductivity k = 1.2 W/m.K, and surface area A = 15 m². Determine (a) the variation of temperature within the wall and the value of temperature at x = 0.1 m and (b) the rate of heat conduction through the wall under steady conditions. - 21

3) The two sides of a large plan wall are maintained at constant temperatures of T₁ = 120°C and T₂ = 50°C, respectively. If you know that the wall thickness L = 0.2 m, thermal conductivity k = 1.2 W/m.K, and surface area A = 15 m². Determine (a) the variation of temperature within the wall and the value of temperature at x = 0.1 m and (b) the rate of heat conduction through the wall under steady conditions. - 21

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a wall that is 5 m high, 8 m long, and 0.22 m thick. The thermal conductivities of the various materials used, in W/m °C, are kA = kF = 2, kB = 8, kC = 20, kD = 15 and kE = 35. The left and right surfaces of the wall are maintained at uniform temperatures of 300 °C and 100 °C, respectively. If the heat transfer through the wall is one-dimensional, determine (a) the rate of heat transfer through the wall; b) the temperature at the point where sections B, D, and E meet, and c) the temperature drop across section F. Disregard any contact resistances between the interfaces.
Heat is produced in a long resistance wire q.u= 1.5 W/cm3. The radius of the wire is given as r1=0.3 cm and the thermal conductivity coefficient as ksteel=18 W/m.K. In addition, the wire is covered with a 0.4 cm thick plastic layer with a thermal conductivity coefficient of kplastic = 1.8 W/m.K. The outer surface of the plastic layer loses heat with an average heat transfer coefficient of h=14/W/m2K and by convection to the ambient air at T∞ =250 C. Considering the interface temperature as T1 and accepting the heat transfer as one-dimensional;
6. a. The heat flux applied to the walls of the biomass combustion furnace is 20 W/m2. The furnace walls have a thickness of 10 mm and a thermal conductivity of 12 W/m.K. If the wall surface temperature is measured to be 50oC on the left and 30oC on the right, prove that conduction heat transfer occurs at a steady state!b. Heating the iron cylinder on the bottom side is done by placing the iron on the hotplate. This iron has a length of 20 cm. The surface temperature of the hotplate is set at 300oC while the top side of the iron is in contact with the still outside air. To reach the desired hotplate temperature, it takes 5 minutes. Then it takes 15 minutes to measure the temperature of the upper side of the iron cylinder at 300oC. Show 3 proofs that heat transfer occurs transiently
Q.3) The two sides of a large plan wall are maintained at constant temperatures of T₁ = 120°C and T₂ = 50°C, respectively. If you know that the wall thickness L = 0.2 m, thermal conductivity k = 1.2 W/m.K, and surface area A = 15 m². Determine (a) the variation of temperature within the wall and the value of temperature at x = 0.1 m and (b) the rate of heat conduction through the wall under steady conditions. (10 Pts)
Heat is lost through the glass pane of a window. The thickness of the glass is 3 mm, and the window is 0.9 m by 1.8 m. The thermal conductivity of glass is 0.8 W/mK. If the temperature difference across the glass is 17 K, what is the total heat transfer through the pane of glass? Give your answer in Watts to the nearest integer.
The exterior wall of a house is composed of a 20 cm thick layer of ordinary brick (conductivity 0.72 W/m K) and a 2.5 cm layer of plaster (conductivity 0.17 W/m K ) on each side (two layers in total). Other purely conductive resistances can be neglected, such as the layer of paint on both sides of the wall. Assume the outer face of the wall is at 35 °C and the inner face is at 20 °C and fill in the gaps. The magnitude of the heat flux through the wall corresponds to the _________ W/m2 and is perpendicular to the wall ________________(fill in with "outside-in" or "inside-out") of the environment. If the wall has a total area of 300m2, the heat transfer rate corresponds to ___________________
EXAMPLE = wire Consider a long resistance wire of radius ₁ 0.2 cm and thermal conductivity k = 15 W/m . °C in which heat is generated uniformly as a result of resistance heating at a constant rate of g = 50 W/cm3. The wire is embedded in a 0.5-cm-thick layer of ceramic whose thermal conductivity is k = 1.2 W/m °C. If the outer surface temperature of the ceramic layer is measured to be Ts = 45°C, determine the temperatures at the center of the resistance wire and the interface of the wire and the ceramic layer under steady conditions. ceramic 17 Interface Mech. Eng. UOK Wire Ceramic layer T₁=45°C ۳۰/۱۰/۲۰۱۳
. Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k = 2.3 W/m °C, and surface area A = 20 m². The left side of the wall is maintained at a constant tem- perature of T₁ = 80°C while the right side loses heat by con- vection to the surrounding air at T = 15°C with a heat transfer coefficient of h = 24 W/m². °C. Assuming constant thermal conductivity and no heat generation in the wall, (a) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the wall, (b) obtain a relation for the variation of temperature in the wall by solving the differential equation, and (c) evaluate the rate of heat trans- fer through the wall. Answer: (c) 6030 W
A cylindrical pipe is made up of two materials. The inner material A, which has thermal conductivity of ka, has inner radius ra and outer radius re. On the other hand, the outer material B, which has thermal conductivity of kb, has inner radius re and outer radius rb. Contact resistance between the two materials is known to be hc. The temperature at the inner radius of material A (at ra) is Ta, while the temperature at the outer radius of material B (at ri) is T3. Find an expression for the temperature at the inner radius of material B (at r.) in terms of the given variables.
Q30) A 4-mm-diameter and 5-m-long electric wire is tightly wrapped with a l1-mm thick plastic cover whose thermal conductivity isk = 0.2 W/m °C. Electrical measurements indicate that a current of 15 A passes through the wire and there is a voltage drop of 8 V along the wire. If the insulated wire is exposed to a medium at T 30°C with a heat transfer coefficient of h = 15 W/m2 °C, determine the temperature at the interface of the wire and the plastic cover in steady operation. Also determine whether doubling the thickness of the plastic cover will increase or decrease this interface temperature..
a. The wall of a building has a surface area of 50 m2. The outside layer of the wall is 20 cm thick concrete with thermal conductivity kcon = .8 W/m-K. The inner layer is 10 cm thick balsa wood (kbalsa = .048 W/m-K) as an insulator. Outside temperatures of 47o C are expected, while an inside temperature of 21o C is maintained by the cooling system. Find the rate of heat transfer through the wall.