3 Brass cube "p = 8530 kg/m , c= side length = 9 mm, are annealed by heating them first to 813°C in a furnace and then allowing them to cool slowly to 130°C in ambient air at 28°C. If the average heat transfer coefficient is 19.9 W/m .°C, If 2204 balls are to be annealed per hour, what is the total rate of heat transfer (watts) from the balls to the ambient air? 380 J/kg.°C, k = 110 W/m.°C, a = 33.9E-6 W/m.°C", %3D

3 Brass cube "p = 8530 kg/m , c= side length = 9 mm, are annealed by heating them first to 813°C in a furnace and then allowing them to cool slowly to 130°C in ambient air at 28°C. If the average heat transfer coefficient is 19.9 W/m .°C, If 2204 balls are to be annealed per hour, what is the total rate of heat transfer (watts) from the balls to the ambient air? 380 J/kg.°C, k = 110 W/m.°C, a = 33.9E-6 W/m.°C", %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider steady-state conditions for one-dimensional conduction in a plane wall having a thermal conductivity k = 40 W/m-K and a thickness L = 0.4 m, with no internal heat generation. -T2 L Determine the heat flux, in kW/m2, and the unknown quantity for each case. Case T1(°C) T2(°C) dT/dx(K/m) 9% (kW/m²) 1 50 -20 i i -30 -10 i i 3 70 i 160 i 4 i 40 -80 i i 30 200 i LO
Consider steady-state conditions for one-dimensional conduction in a plane wall having a thermal conductivity k = 40 W/m-K and a thickness L = 0.3 m, with no internal heat generation. -T2 L Determine the heat flux, in kW/m², and the unknown quantity for each case. Case T1(°C) T2(°C) dT/dx(K/m) q (kW/m?) 1 50 -20 i i 2 -30 -10 i i 3 70 i 160 i 4 i 40 -80 i 5 i 30 200 i
2.33 One end of a 0.3-m-long steel rod is connected to a wall at 204°C. The other end is connected to a wall that is maintained at 93°C. Air is blown across the rod so that a heat transfer coefficient of 17 W/m2 K is maintained over the entire surface. If the diameter of the rod is 5 cm and the temperature of the air is 38°C, what is the net rate of heat loss to the air? 0.3 m- Wall Wall 204°C 93°C Steel rod 5-cm diameter Air 38°C Problem 2.33
The total consumption of electrical energy in the United States is about 1.0 1019joules per year.What is the average rate of electrical energy consumption in watts?If the population of the United States is 300 million, what is the average rate of electrical energy consumption per person?The sun transfers energy to the earth by radiation at a rate of approximately 1.0 kW per square meter of surface. If this energy could be collected and converted to electrical energy with 40 % efficiency, how great an area (in square kilometers) would be required to collect the electrical energy used by the United States?
Q.3) The two sides of a large plan wall are maintained at constant temperatures of T₁ = 120°C and T₂ = 50°C, respectively. If you know that the wall thickness L = 0.2 m, thermal conductivity k = 1.2 W/m.K, and surface area A = 15 m². Determine (a) the variation of temperature within the wall and the value of temperature at x = 0.1 m and (b) the rate of heat conduction through the wall under steady conditions. (10 Pts)
A house, for cooling purposes, consists of two zones: the atric area zone A and the living area zone B (see below figure). The living area is cooled by a 2 -ton air conditioning unit that removes 23,000 Btu/hr. The heat capacity of zone B is 1/6 °F per thousand Btu. The time constant for heat transfer between zone A and the outside is 3ℎr, between zone B and the outside is 6ℎr, and between the two zones is 6ℎr. If the outside temperature stays at 90°F, how warm does it eventually get in the attic zone A ?
3. 100-gram oil at 20°C and 50-gram iron at 75 °C are placed in 200-gram iron container. The increase in temperature of the container is 5°C and the specific heat of oil is 0.43 cal/g °C. What is the specific heat of the iron?
3.4 Estimate the rate of heat loss due to radiation from a covered pot of water at 95 ° C. How does this compare with the 60 W that is lost due only to convection and conduction losses? What amount of energy input would be needed to maintain the water at its boiling point for 30 minutes? The polished stainless steel pot is cylindrical, 20 cm in diameter and 14 cm high, with a tight-fitting flat cover. The air temperature in the kitchen is about 25 ° C. State any assumptions you make in deriving your estimates
The inside wall of a furnace is at 2100oF and the outside wall is at 300oF. The wall of a furnace must be designed to transmit no more than 220 Btu/hr-ft2. Two types of bricks are available for construction:TYPE A: k = 0.38 Btu/ hr-ft-R with an allowable maximum temperature of 1400oFTYPE B: k = 0.98 Btu/ hr-ft-R with an allowable maximum temperature of 2300oF Both types of bricks have the same dimensions (9” x 4.5” x 3”) but the cost for Type B brick is twice the cost of Type A brick. Illustrate the order of arrangement of bricks A and B in the furnace wall (with thickness, estimated temperatures at the interface between walls A and B and at the interior and exterior surface, the transport area and direction of transfer included)
(B) A cylinder made of aluminum has a mass of 7 Kg and initially at a temperature of 250 C is suddenly placed in a controlled environment in which the temperature is maintained at 15 'C. The convection heat transfer coefficient is 90 W/(m2. C ). Calculate the time required to cool the cylinder to 100 °C. Use the lumped capacity method. Take p=2707 kg/m³, C=896 J/kg°C, L=15cm.
As shown in the sketh below, a steam pipe of 0.12-m inside diameter is insulated with a layer of calcium silicate. "2. Ta2} 1. Ta,1} Steam Insulation (a) If the insulation is 10 mm thick and its inner and outer surfaces are maintained at T, = 800 K and Ta = 490 K. respectively,. what is the rate of heat loss per unit length (q) of the pipe, in W/m? (b) Determine the rate of heat loss per unit length (d), in W/m, and outer surface temperature T,2, in K, for the steam pipe with the Inner surface temperature fixed at T = 800 K, inner radius = 0.06 m, and outer radius n = 0.18 m. The outer surface is exposed to an airflow (T 25°C) that maintains a convection coefficient of h = 25 W/m2-K and to large surroundings for which Tur = T, = 25°C. The surface emissivity of calcium silicate is approximately 0.8.
A solid hemisphere of radius 5 cm to be cooled in air (at 20 o C, h=10 W/m 2 .K) from 200 oC to center of 150 oC, assume following sphere properties ρ=8500kg/m3, k=20W/m.K , C=400 J/kg.Ka. List assumptions and justify selected method of solution b. How long does it take to cool the hemisphere? c. What is the temperature of the surface at end of cooling?