3. A sealed Styrofoam container is filled with water ico at 0° C. The thickness of the Styrofoam is 2.0 x 10° m and the outer surface area of the container is 0.016 m2. The temperature outside the Styrofoam container is 35° C. What mase of ice melts in one hour (due to heat conduction through the sealed Styrofoam container)?

3. A sealed Styrofoam container is filled with water ico at 0° C. The thickness of the Styrofoam is 2.0 x 10° m and the outer surface area of the container is 0.016 m2. The temperature outside the Styrofoam container is 35° C. What mase of ice melts in one hour (due to heat conduction through the sealed Styrofoam container)?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A fuel pump is delivering 50 gals/min of oil with a specific gravity of 0.75. The total head is 30 meters. Find the motor that is capable of handling this pump in horsepower. Assume pump efficiency of 70% and motor efficiency of 80%. Select from the available motors provided: 1hp, 1.25hp, 1.5hp, 2 hp.
Hello, I hope you are fine. I need to do this homework in Metal Engineering. I hope to get your help because I have an important homework.
Q3: Explain how you would produce a hard surface in the followings, Give reason(s) for your selection. 1-A shaft made from 1% Al-1.5 % Cr steel which has to operate at a temperature between 350 and 400°C. 2-A gear wheel made from a 0.5% C steel which requires a hard surface to improve its wear-resistant properties. 3-An automobile axle requires an accurate thickness of the hardened case. 4-Large quantities of low carbon steel parts. 5-Very high wear resistance surface.
Q3B) A metal is fabricated by drawing at 125 °C. The metal melting temperature is 400 °C. Find by calculation whether this foming process is cold or wam or hot working. Ans--
I need the answer as soon as possible
A machinist was tasked to insert an aluminum piston into a steel cylinder. The inside diameters of the cylinder and of the piston are 0.500 m and 0.4998 m, respectively, at 25OC. To what temperature must they be heated to obtain a perfect fit?
Q.B3. As part of a project, students have been asked to cast an Aluminium disc for use as a flywheel. The flywheel is part of an engine development project and needs to be 200 mm in diameter and 20 mm thick. Green sand casting will be used. The shrinkage associated with this metal and process is 5% at the solidification stage and further 3 % on cooling to room temperature. Aluminum has a density of 2710 kg/m³ and a melting temperature of 660°C. The pouring temperature is 700°C while the specific heat of aluminum is 887 J/kg.K. The latent heat of fusion of Aluminum is 396 kJ/kg. From previous experiments the Chorinov constant for the mold was found to be 10 s/mm². Determine: a.) The dimensions of the pattern (diameter and thickness) that will need to be made for this part (ignore riser and sprue). b.) The time it will take for complete solidification of the part. c.) Assuming an electric furnace at 10% efficiency is used to heat the metal and it takes around 2 hours achieve pouring…
What is the difference between direct and shear stress?
Consider the casting in (Figure 1). Figure 20 mm 40 mm 120 mm 40 mm 1 of 1 Part A Determine the distance to the center of mass of the casting that is formed from a hollow cylinder having a density of 3.2 Mg/m³ and a hemisphere having a density of 3 Mg/m³. Express your answer to three significant figures and include the appropriate units. IN = μᾶ Value Submit Previous Answers Request Answer X Incorrect; Try Again Units < Return to Assignment Provide Feedback ?
The answer is one of the options below please solve carefully and circle the correct option Please write clear .
What is the basis of all calorimeter calculations for specific heats of materials? Can someone please answer? I don't know how the question is worded.
Obtain pieces of steel, wood, and concrete of known volume. Find pieces with simple shapes, so that you can measure the dimensions and calculate the volume quickly. Determine their mass by placing each on an accurate scale, and calculate their densities.