A weight W= 120 kN is being supported by steel sections with force T, force F, and force C. The coordinates of A, B, C, and D are given. Assume that E is the origin (0,0,0). Determine Forces T, F, and C. CK 芽 2.45 m 1.22m 0.90 wwon 1.25 m 1.85 m Br W=120 KN

Q: How do you convert gpm to ft?

A: A cross-sectional area's flow of fluid is measured in gallons per minute. In simple terms, it…

Q: Name four methods of flow measurement?

A: Name four methods of flow measurement?

Q: DEFINE WATER RESOURCES PLANNING (in your own understanding/150-200 words)

A:

Q: Design a typical layout model for a Water Supply Scheme

A: Brief Concept- Water Supply Scheme- It is the set up of different units for the treatment of water…

Q: Could you show the calculations for the table

A: The discharge through the section = Q = 100, 150, 200, and 250 cfs The slope of the section = S =…

Q: What are the three parts of a technical section under the CSI Format?

A: CSI stands for Construction Specifications Institute. It is the organization which publishes the…

Q: A triangle has an area of 14 sq ft and a base of 7 feet. What is the height of thetriangle?

A: given data :  area of triangle (A) = 14 square feet  base (b) = 7 feet  height (h) = ?

Q: In detail what is the CSI MasterFormat and what is listed in division 28?

A: Answer  CSI MasterFormat also known as "Dewey Decimal system" is the product of the Construction…

Q: name 2 main categories of sewage disposal systems

A: Sewage is the wastewater produced by the community. It is generated by residential, commercial,…

Q: Write short notes on any two of the following: PPRA a) b) DPR

A:

Q: Identify the portion of a foot (12") as indicated by the reading from the zero mark (0) on the scale…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: Illustrate a simple drawing plan of pipeline

A: Simple drawing plan of pipeline: The piping plan or general arrangement drawings show all major…

Q: Compute total indeterminacy

A: Given data : Number of external support reaction (R)=2+2+2=6 Number of member attach at hinge joint…

Q: What is the most common use of RFI?

A:

Q: computer aided engineering

A: Computer-aided engineering (CAE) is the use of computer software to simulate performance in order to…

Q: What are the Steps in drawing a flow net?

A: - A Flow net is defined as the graphical representation of two dimensional water flow in a soil mass…

Q: Draw figures to show N60E, S15E and S30W .

A: The figure showing N60E is given below.

Q: Describe Source Correction Method.

A: Solution: The source correction method is the effective method that is used as effective methods to…

Q: +4

A: Given

Q: Line standard End standard How will you determine if the measurement methods described above is a…

A: Line Standard: Measurement of the distance between  two lines is known as Line standard. For wide…

Q: RITING ITLED d. What is the difference in elevation between TP15 and TP30? (Ans.) e. What is the…

A:

Q: Briefly describe the CSI Specifications?

A: CSI stands for the Construction Specification Institute. CSI has introduced a common format for…

Q: Line P to Q intersects the street alignment as shown in the sketch below. What is the length of line…

A:

Q: (b) Design the Beam B-B for the maximum sagging section only. Your design should consider the…

A: L=4.55 mh=22.2 mt=122 mmDL=3.55 kPaLL= 4.55 kPafck= 25.5 Mpafy=472 MpaTo design- 1) Loads2) Design…

Q: Grades of g₁ = -2.50% and 9₂= +1.50 %, VPI elevation 856.00 ft at station 22 +00, and a fixed…

A: .Field conditions require a highway curve to pass through a fixed point Compute a suitable…

Q: What is “excess” scale (esp. CaCO3) a concern for water utilities? (answer in three to five…

A: Excess scale specially Calcium carbonate is a concern for water utilities due to 1. increased…

Q: Break the shaded area into the five different areas shown. Find the area and the x- and…

A:

Q: How exactly does one use a report generator, and what precisely is meant by a mock-up report?

A: Using a valid, reliable report generator ensures a clean and consistent availability of information…

Q: 134 438 124 295 408 139 What is the correct phasing design for the 87 318 163

A: Given a four-legged intersection as shown below Required: To choose correct phasing design from the…

Q: Define SLS requirement

A: Solution: A Service level specification basically forms a part of the service level agreement in…

Q: What is the main requirement for a BIM approach ?

A: Brief Concept Introduction- BIM- BIM stands for Building Information Modeling. BIM is a very vast…

Q: Describe the MODIFIABLE and NON-MODIFIABLE risk factors of CAD

A: Risk factors which can be altered through a variety of lifestyle modifications are referred to as…

Q: Expose the practise of penetration testing if it exists. How safe is my information, exactly?

A: Penetration testing is a commonly used practice to assess the security of an organization's…

Q: What is expert determination?

A: Experts are often assigned by justices and adjudicators in national courts and arbitration…

Q: Station End area fill (sf) Distance (ft) Volume (cy) 150 + 00 360 150 + 50 3,500 50 151 + 00 10,400…

A: use mean area method to find the volume mean area is found out by using Amean=A1+A22volume V=…

Q: An electric motor M is used to reel in cable and hoist a bicycle into the ceiling space of a garage.…

A:

Q: Please double check the answer if this is correct!

A: Given, σall = 300 kPa a = 20 mm b = c = 250 mm

Q: 7. Usually the minimum height in the room should not be lower than ( A. 2.2 m B. 2.0 m C. 2.4 m…

A: Note: Multiple questions are asked. Therefore, as per Bartleby guidelines, the answer of only…

Q: What are the advantages of using GIT?

A: Advantages of Git:-  1. Performance Git performs very strongly and reliably when it was compared…

Q: When drawing a plan in AutoCAD, the user will draw the actual dimension of the building. True False

A: When drawing a plan in AutoCAD, the actual dimension of buildings are not drawn but their scaled…

Q: I x,0= 10 " I yo = r x,0 = 4"X6"X ½" r yo = 12" 4"X 8"X 1" | 1" 12 "

A:

Q: What is filter drag model?

A: Answer:- Filter Drag Model:- The resistance across the fabric dust layer is called filter drag. The…

Q: When does retention get released?

A: Retention is a percentage normally 5% of the total amount which is approved due to the contractor on…

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.