What is the USGBC Web?

Q: In detail what is the CSI MasterFormat and what is listed in division 28?

A: Answer  CSI MasterFormat also known as "Dewey Decimal system" is the product of the Construction…

Q: Uniform, and Non- uniform flow

A: uniform flow= when parameters of fluid like velocity and depth etc. won't change with space at any…

Q: Determine the centroid of the beam's cross-sectional area and then compute the moment of inertia…

A:

Q: ncentration of 100 mg/L using a settling column was carried out in a oratory. The results of the…

A: Given - L = 45 M B= 12 m Q =8.1 MLD  =8.1×106 LD     Q =8.1×103  m3/sec24×60×60      Q=0.09375…

Q: A short circular column of 400 mm diameter and eight 20 mm diameter longitudinal bars is subjected…

A: The following is the given data, Circular column diameter = 400 mm Reinforcement = 8 - 20mm Factored…

Q: For the circular arch, find the internal axial force at a location 5 m to the right of point A. Use…

A:

Q: A right cylindrical container of diameter D (meter) and H (meter) high is filled with water Z…

A: Given, D= 1.2m b=350mm t=250mm H= 4.5 m Z= 3.0m L=3.0m

Q: A centrifugal pump is to operate at 250 cfs, H₂ = 400 ft, Dp = 36 inches, N= 870 rpm. A model test…

A: Qp = 250 cfsHp = 400 ftDp = 36 in N = 870 rpm Qm = 5 cfs

Q: conducted an aquifer of sandy soil 4 m thickness confined between two impervious strata. When…

A:

Q: (Single pipe with pump) The pump shown in the figure below adds a 13-ft head to the water being…

A: Introduction- A pump is a machine that transports liquid (liquids or gases). Pump are divided into…

Q: In terms of nature of manifestation the measurement error consists of two major components -…

A: Random errors and systematic erroors are the measurement errors.

Q: POLYMER STRUCTURE based us Fibers, Plastics, or Elastomers

A: thanks for posting your question   you haven't mentioned in how many words you want the report on…

Q: 4. A block of wood floats in water with 6 inches projecting above the water surface. If the same…

A:

Q: Uploaded

A: (a)Find the moment at point O, when the load is pushed perpendicular to the wrench arm.Write the…

Q: What distinguishes open source software from closed source software? compile a list of every GIS…

A: Context: GIS Applications, Open source vs close ed source assest

Q: Figure 2

A:

Q: A foundation is constructed in a soil with the following parameters: c' = 5.0kN/m? y = 18.5 kN/m³ Ø'…

A: The given data is: B=2 m L=3 m C'=5 KN/m2 Q=3000 KN M=300 KN-m calculating eccentricity:…

Q: What is the Design mode?

A: In terms of construction, the word design mode refers to the process of creating a specific solution…

Q: A block of wood weighing 640kg/m³ is in the shape of a rectangular parallel piped having a 10 cm.sq.…

A:

Q: 3- is the factor affecting the measurement of standard consistency of thecement paste?

A: Introduction : A cement paste's standard consistency is defined as the proportion of water added in…

Q: A sphere 850mm-diameter floats half submerged in a tank of oil (sg=0.90) What is the total vertical…

A:

Q: Locate the centroid i and ỹ of the shaded area shown.

A:

Q: What is the CSI Project manual?

A: The CSI Project Manual is the authoritative resource for organisation, preparation, use and…

Q: QUESTION 4 Water at 10 C flows in a 1.3-cm-diameter pipe at a rate of 1.33 L/min. The hydrodynamic…

A: D = 1.3 cm or 0.013 m  Q = 1.33 L/min

Q: 50 units 50 units A B C Which rivet is least likely to fracture first? a O A b O B C Ос d The rivets…

A:

Q: Following bearings were observed while running a closed traverse. Correct the bearing for local…

A:

Q: Determine the absolute pressure of the water in the pipe at B if the tank is filled with crude oil…

A: Patm =101kPa H=1.5m To find absolute pressure at B

Q: Define GIS.

A:

Q: A cylindrical tank, 2.50-m diameter and 5.0m high weighs 3250 N. The tank float in water with a…

A:

Team Management

To complete a specific task or to accomplish organizational goals along with increasing work productivity, individuals need to come together and think along a common path and direction. There are certain tasks in an organization that cannot be done alone and the involvement of more individuals is essential. These groups of individuals who work together for a common goal compose a team and the individual members involved are known as team members.