A closed cylindrical tank 2m in diameter and 5m tall has 1.5m of oil (SG = 0.80), 0.5m of an unknown liquid (SG = 1.2) and 2m of water. There is a 30KPA pressure at the top of the tank. Determine the discharge through a 120mm diameter orifice at the bottom of the tank if coefficient of discharge is 0.96. A) No Answer among the choices B 103.72 L/s 114.97 L/s D 95.56 L/s 87.23 L/s

A closed cylindrical tank 2m in diameter and 5m tall has 1.5m of oil (SG = 0.80), 0.5m of an unknown liquid (SG = 1.2) and 2m of water. There is a 30KPA pressure at the top of the tank. Determine the discharge through a 120mm diameter orifice at the bottom of the tank if coefficient of discharge is 0.96. A) No Answer among the choices B 103.72 L/s 114.97 L/s D 95.56 L/s 87.23 L/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q// A (300mm) diameter of pipe, if the discharge (90 L/sec), nozzle diameter (75mm) and pipe length from (1 to 2) was (100m) Determine the length of pipe from (2 to 3), and the pressure at point (2). (e=0.026mm, v =1.13* 10“ m/sec). Fig(1). 6m 23m Fig.(1) Nozzle
Question 2: An 8 in diameter (f=0.028) 500 ft long discharge a 3 in diameter water jet into the atmosphere at a point which is 250 ft below the water surface at intake (Figure 2). The entrance to the pipe is reentrant with ke=0.9 and the nozzle loss coefficient kn=0.045. Find the flow rate and pressure head at the base of the nozzle. D, L, f B kn T D₁ -V₁
For the system in the figure, calculate the distancevertical between the surfaces of the two tanksWhen water at 10°C flows from point A to point B, arate of 0.03 m3/s. Elbows are standard. Thetotal length of 3 inch tube is 100meters. The length of the 6-inch pipe is 300 m. (T)
Q2: For the system shown below, find the minimum flow rate of the jet from the orifice at the end of the pipeline (at point A) to cross the wall and minimum pump head (Hp) that required to maintain the required minimum head (hme) required to discharge this flow rate. Take Z1 between O to 10 m , 2 from O to 9 m and Cv-0.85. Total Energy line 3.5 m z1 d= Somm 22 2.0 m Concrete wall Solution:
None
Q/In Figure No. (4) the value of pressure of compressed air pa in pipe No.(1) is 3.8 (Bar). Find the value of pressure of water pg in pipe No. (2). B Pipe No.(2) water comressed Air Pipe No.(1) 4.5m water xA 2.7m 1.2m Air (2) (1) Fig.(4) Mercury
A (300mm) diameter of pipe, if the discharge (90 L/sec), nozzle diameter (75mm) and pipe length from (1 to 2) was (100m) Determine the length of pipe from (2 to 3), and the pressure at point (2). (e=0.026mm, v =1.13* 10" m²/sec). Fig(1).
Water is pumped up from a reservoir to a smaller holding tank. If the flow rate through the pipe is 50 LPM, find the NPSH available immediately before the pump. The length of the pipe from the reservoir to the pump is 13.1 meters, and its diameter is 2.8 cm. The distance is h2=6.8 m. Assume a friction factor of 0.021. The vapor pressure of water at the current temperature is 2,399 Pa. Current atmospheric pressure is 95,194 Pa. The density of water is 991 kg/m^3
At night, water is pumped from a treatment plant reservoir through distributing piping to an elevated storage tank. Assume no other withdrawals from the system. The water surface in the supply reservoir is at 3m elevation, the lift pump elevation is 6m, the water elevation in the elevated tank is 42m. The pipe network maybe considered equivalent to 1500m of 250mm diameter. Use C=100. There is a supply of 60 Liters/sec. to the tank. a. Compute the head loss of the 250mm diameter pipe. b. Compute the pump discharge pressure required to supply a flow of 60L/s to the tank, c. Compute the slope of the energy gradient
A closed cylindrical tank 3m high and 1m in diameter contains 1.2m of oil (SG = 0.8), 1m of water and air under a pressure of 16 KPa. A 125mm diameter orifice is placed at the vertical side of the tank, 300mm from the bottom. Determine the actual discharge at the orifice if C = 0.94. Hide answer choices A 98.61 L/s B) 103.01 L/s C No answer among the choices 96.83 L/s E) 92.69 L/s
The allowable Net Positive Sustion Head (NPSH) for a pump provided by the manufacturer for a flow of 0.05 m³/s is 3.3 m. The temperature of water is 30° C (vapour pressure head absolute = 0.44 m), atmosphere pressure is 100 kPa absolute and the head loss from the reservoir to pump is 0.3 N-m/N. Find the maximum height of the pump above the sustion reservoir.
Choose the correct answer a-0.54 t, 22.30 , 0.707 t b-0.45 t, 0.707 t, 23.20 c-Nothing mentioned d-0.45 t, 0.707 t, 22.30 e-0.707 t, 0.45 t, 22.30