I need quick answer.... 4) Two tanks of liquid with v-1.02x10-6 m²/s are connected by two pipes in series as shownin the figure below. If the pipe wall roughness is e, the diameters of the first and the secondpipe are Di and D₂ respectively, the lengths of the first and the second pipes are L, and Larespectively, find the value of H for the given discharge, Q.(Use the given data of your group below.)EPipe 1QPipe 2

Given: D1=0.305mD2=0.610mL1=610mL2=9140mE=0.0030ma=0.0566 m3/s To find: H

4) Two tanks of liquid with v-1.02x10-6 ms are connected by two pipes in series as show in the figure below. If the pipe wall roughness is , the diameters of the first and the seco pipe are D, and D₂ respectively, the lengths of the first and the second pipes are L, and respectively, find the value of 1 for the given discharge, Q. (Use the given data of your group below.) Pipe 1 Pipe 2

4) Two tanks of liquid with v-1.02x10-6 ms are connected by two pipes in series as show in the figure below. If the pipe wall roughness is , the diameters of the first and the seco pipe are D, and D₂ respectively, the lengths of the first and the second pipes are L, and respectively, find the value of 1 for the given discharge, Q. (Use the given data of your group below.) Pipe 1 Pipe 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3. An object with a temperature of 88°C is placed into the water of 25°C. After 15 minutes, the…

A: To given problem can be solved using newton law of cooling, Let, ∅ = temp. of given body ∅∘…

Q: QUIZ 3 FALL 2020 Problem 1. For the frame shown in the figure, determine (a) Reactions at the…

A: Solution-

Q: Part 3 – Hydraulic Jump and Critical Depth –- C4 Flume Channel width = 7.6_cm Flume Slope =3_% Dist.…

A: The given data is shown below: Channel width=7.6 cmFlume slope=3%Distance between gauges=100…

Q: A prismatic tank having variable cross- Atmosphere section (base areas: A¡ = 20 m² and A2 = 10 m²)…

A: dm˙=mass flow rate=ρ2πrdrufrom result…

Q: What soil properties are needed for estimating bearing capacity of driven piles and drilled shafts?…

A: We are authorized to answer one question at a time, since you have not mentioned which part you are…

Q: a) Identify and locate the centroid, ỹ on axis x'- x' for the parts cross-sectional area in Figure…

A: Find centroid Y and moment of inertia about X'X' axis

Q: A rectangular footing 2.0 m by 3.0 m is built in a homogeneous bed of sand of having bulk unit…

A: (a) Assume the last digit of student number as 6. For given angle of shearing resistance, we get

Q: Using the equivalent eccentricity method, select a tied square column cross-section for a short…

A: Geometrical properties of the tied square column. Calculate the factored load Assume the steel…

Q: Determine the number of primary unknows used in displacement method for the statically indeterminate…

A: Degree of indeterminacy 1) Degree of static indeterminacy (DS) It is the sum of External static…

Q: 4. The two vertical rods attached to the rigid bar are identical except for the length. The bar is…

Q: 1. Locate the centroid (£, 9) of the shaded area. 6 in. 3 in. 6 in. 6 in.

A: We are supposed to answer the only the first question, Kindly understand and post other question…

Q: B H.W For the three hingcd arch shown in the figurn, Draw the normal fene, shear force end bendling…

A: Draw free body diagram Consider the summation of forces in the horizontal direction Ax-Cx=0…

Q: If P = 5 kN, determine the average shear stress in the pins at A, B, and C. All pins are in double…

Q: 1. A liquid has a specific gravity of 0.8. Determine its specific weight (in N/m³) and density (in…

Q: 3. A homogeneous bar with a cross-sectional area of 400 mm² is attached to fixed supports as shown…

Q: The bars of the truss each have a cross-sectional area of 1000 mm2lf the maximum average normal…

A: Given Cross sectional area A=1000mm2 Average normal stress=160MPa To find Pmax

Q: A truss is loaded as shown in the figure. Assume AE = 10,000 N. B 10N AE = constant 3 m 3m Determine…

A: A truss is a structure composed of components organized into interconnected triangles, so the entire…

Q: Describe the working principle of screw compressor with figure.

A: Screw compressor It is a type of rotary compressor which help s in compressing air due to screw…

Q: 40 30 20 20 15+ 10 10 10 15 20 25 30 Air temperature, "C 35 Wind velocity, km/h 4 40 35 30 25 20 15…

A: Calculate the rate of evaporation from the following equation: E=5(Tc+18)2.5-r(Ta+18)2.5V+4×10-6…

Q: 1) The velocity distribution for the flow of a Newtonian fluid between two wide, parallel plates is…

A: Newtonian fluid: The fluids are not obeyed Newton's rule is known as Newtonian fluids.…

Q: PROBLEM 2 The table lamp consists of two uniform arms, each weighing 4 N and lengths of 600 mm and a…

Q: Q2) There are two water bodies separated by a rectangular gate having a width of B-2 m. In the left…

Q: Rainwater flows through the galvanized iron downspout shown in the figure below at a rate of 0.009…

A: To determine:The value of D

Q: Determine the maximum weight W that can be supported as shown. Cable FG has a maximum strength of…

Q: Excess or deficiency can only be prorated between found original monuments (or best available…

A: Excess or deficiency can only be prorated between found original monuments (or best available…

Q: 2. The following results were obtained from liquid limit and plastic limit tests conducted on the…

Q: 1. A simply supported beam A carries a point load at its mid span. Another identical beam B carries…

Q: The assembly shown in Fig. P5.39 consists of a solid aluminum alloy [E = 70 GPa] post (2) surrounded…

A: Solution; Given that; E1=100 GPa=100*103 E2=70 GPa=70*103

Q: Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kN force is applied to the…

Q: Draw the Shear and Moment Diagram of the figure shown 40 kn 40 Kn m 50 kn ww www 20 kn 2.0 m 2.0 m +…

Q: The rod AB weighs 35N. Determine the minimum force P to prevent the rod AB from sliding. The contact…

Q: Given the properties and elevations of the three reservoirs, if friction factor f, is 0.01 for all…

Q: 3. Find the reactions at B (fixed support). 2 kN 2 m 1.5 kN/m 2m

A: The reactions at B = ?

Q: The velocity of a particle moving along the x- axis is defined by V = x*3-4x^2+6x where V is in m/s…

Q: 4. To what height will water rise in a 3mm-diameter glass tube at 20°C? Assume Owater = 0.073 and…

A: As per students demand i have provided solution to question 4,if required solution of all, please…

Q: What is the total actual factored design load for 350 x 500 mm beam of length 15 meters and a live…

Q: Determine the magnitude of the reactions on the beam at B. Neglect the thickness of the beam. 10 N.m…

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

I need quick answer....

4) Two tanks of liquid with v-1.02x10-6 m²/s are connected by two pipes in series as shown
in the figure below. If the pipe wall roughness is e, the diameters of the first and the second
pipe are Di and D₂ respectively, the lengths of the first and the second pipes are L, and La
respectively, find the value of H for the given discharge, Q.
(Use the given data of your group below.)
E
Pipe 1
Q
Pipe 2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step by step

Solved in 7 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need the answer as soon as possible
What is the discharge in pipe 1? A. 0.61 B. 0.90 C. 0.49 D. 0.68
I need the answer as soon as possible
A differential "U"-tube manometer containing mercury of density 13000 kg/m³ is used to measure the pressure drop along a horizontal pipe. If the fluid in the pipe is water and the manometer reading is 0.65m, what is the pressure difference between the two tapping points? Fluid density Pw A B a b datum Manometric fluid density p Hg Figure of manometer setup
1) The figure shows a conduit made of 1 std type K drawn copper tubing that conveys acetone at a flow rate of 1.33x10 m³/s. All fittings are soldered; the gate valve is fully open. (a) calculate the pressure drop through the system using minor-loss values. (b) Calculate the pressure drop through the system using equivalent length values. Compare the results. The total length of tubing is 9.15 m and the conduit is in a horizontal plane.
A fire protection system is supplied from a water tower with a bent pipe as shown in the figure. The pipe friction f is 0.03. Ignoring all minor losses, the maximum discharge Q in the pipe is 25 m 4 d = 100 mm 150 m Q
Solve using the hardy cross method.Iterate 2 times by hand in bond paper. Iterate 18 times by spreadsheet in tabular form in Excel.
Two pipes are connected in parallel. One pipe is twice the diameter of the other and three times long. Assume that f in the larger pipe is 0.010 and f in the smaller is 0.014. Determine the ratio of the discharges of the two pipes.
Kindly give me right solutions with clear calculations
Four reservoirs have pipes that meet at a common junction. Their characteristics are as follows: (see table) If the friction factor, f = 0.015 for all pipes, determine the following: a. discharge of pipe Ab. discharge of pipe Cc. discharge of pipe D
c) The orifice flowmeter shown in Figure 4 is used to obtain the flowrate of oil inside a conduit. The diameter of the orice, d is one third of the pipe diameter, D with pressure difference recorded as 25 kPa. The pipe diameter D is 6 cm, discharge coefficient Ca, is 0.60, Bis the ratio of orifice diameter to pipe diameter and Oilspedific gravity, SG is 0.95. If the h is 7 cm, i. Calculațe the vollime flowrate of oil inside the conduit. ii. Determine the mass flowrate of oil inside the conduit. iii. Explain why the discharge coefficient Ca, for the orifice meter is higher compared to the venturi and nozzle meters. D=6 cm d Figure 4
A 160 mm pipe branches into a 100 mm pipe and a 50 mm pipe, as shown in the figure. In both pipes, as indicated, they are made of hydraulic copper 30 m long, the fluid that circulates is water at 10°C. Determine what the resistance coefficient K of the valve should be to obtain equal flow rates of 400 L*7min in each branch