7-40. SAE 30 oil at 68°F flows through the piping system shown in Figure 7.38. (a) If Q₂ = 20 gpm, what is the largest allowable value of Q, so that the flow in inlet pipe 1 is laminar? (b) For the calculated value of Q₁, determine whether the flow is laminar or turbulent in pipes 2 and 3. Globe valve 1 in. dia. 1.25 in. dia. 1.25 in. dia.. Pipe 4 21->>> Pipe 1 f Pipe 2 Pipe 3 Globe valve 3/4 in. dia.. Figure 7.38 System for Exercises 7-40 and 7-41. 24

7-40. SAE 30 oil at 68°F flows through the piping system shown in Figure 7.38. (a) If Q₂ = 20 gpm, what is the largest allowable value of Q, so that the flow in inlet pipe 1 is laminar? (b) For the calculated value of Q₁, determine whether the flow is laminar or turbulent in pipes 2 and 3. Globe valve 1 in. dia. 1.25 in. dia. 1.25 in. dia.. Pipe 4 21->>> Pipe 1 f Pipe 2 Pipe 3 Globe valve 3/4 in. dia.. Figure 7.38 System for Exercises 7-40 and 7-41. 24

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q/In Figure No. (4) the value of pressure of compressed air pa in pipe No.(1) is 3.8 (Bar). Find the value of pressure of water pg in pipe No. (2). B Pipe No.(2) water comressed Air Pipe No.(1) 4.5m water xA 2.7m 1.2m Air (2) (1) Fig.(4) Mercury
A (300mm) diameter of pipe, if the discharge (90 L/sec), nozzle diameter (75mm) and pipe length from (1 to 2) was (100m) Determine the length of pipe from (2 to 3), and the pressure at point (2). (e=0.026mm, v =1.13* 10" m²/sec). Fig(1).
A closed cylindrical tank 3m high and 1m in diameter contains 1.2m of oil (SG = 0.8), 1m of water and air under a pressure of 16 KPa. A 125mm diameter orifice is placed at the vertical side of the tank, 300mm from the bottom. Determine the actual discharge at the orifice if C = 0.94. Hide answer choices A 98.61 L/s B) 103.01 L/s C No answer among the choices 96.83 L/s E) 92.69 L/s
The system shown is in a vertical plane and the fluid has a relative density of 0.80. The pressure at point 1 is 260kPa, and the flow rate is 0.090 m3/s. Determine the reactions at the support at A.
P-4 fuel (SG = 0.77) flows rough the Venturi meter hown in the figure below with a velocity Vo= 14.8 ft/s in the d1=6.00-in. pipe. In viscous effects are negligible, determine the elevation, h, of the fuel in the open tube connected to the throat of the Venturi meter. Assume h1= 7.70 in., h2= 5.70 ft, d2= 4.00 in.
answer quickly
The venturi meter is being used to measure the flow of fuel oil (sp gr = 0.858). The differential gage fluid is water. The meter coefficient is 0.975. Compute the discharge if z is 16 inch. 3 inch 1 inch echplic.c
3)a: For the figure below, find the discharge in pipe, neglect the minor losses only. (e-0.001m, D-Im, L-600m, u-1.307*10 m/sec). LAS 5m 2 1.96 D. b: In a pipe of 300 mm diameter the maximum velocity of the flow is found to be 2 m/s. If the flow in the pipe is laminar, determine: 1) The average velocity and the radius at which having the same velocity magnitude as the average velocity. 2) The velocity at 50 mm from the wall of the pipe. 5964 11.62
A 30 cm diameter pipe is connected by a reducer to a 10 cm diameter pipe. Points 1 (on the 30 cm diam.) and 2 (on the 10 cm diam.) are along the same elevation. The pressure at 1 is 250 KPa. The flow is 50 liters per second and the energy lost between 1 and 2 is equivalent to 20 KPa. Compute the pressure at 2 if the liquid flowing has a specific gravity of 1.30.
Time: 60 Q1: pump puts 2kw in to the system. Find: b. The pressure in the pipe on section side of the pump (at C). a. Discharge. C 5 kPa L = 200 m 10m ↓ Air Water 55 marks 15 m P L = 50m D = 6 cm f = 0.025 D = 8 cm f = 0.030
height of water the pressure intensity : () at the interface of the two liquids, and (ii) at the bottom of the tank. [Ans. () 1.57 N/cm", (il) 3.04 N/em 6. An open tank contains water upto a depth of 1.5 m and above it an oil of sp. gr. 0.8 for a depth of 2 m. Find 7. The diameters of a small piston and a large piston of a hydraulic jack are 2 cm and 10 cm respectively, A force of 60 N is applied on the small piston. Find the load lifted by the large piston, when: (a) the piston at the same level, and (b) small piston is 20 cm above the large piston. The density of the liquid in the jackis [Ans. (a) 1500 N, (b) 1520.5 NJ kg given as 1000 - 8. Determine the gauge and absolute pressure at a point which is 2.0 m below the free surface of water. Take [Ans. 1.962 N/cm? (gauge), 12.066 N/cm? (abs.)] - atmospheric pressure as 10.1043 N/cm?. 9. A simple manometer is used to measure the pressure of oil (sp. gr, = 0.8) flowing in a pipe line. Its right limb is open to the atmosphere and left…
2. A discharge of 8.5 L/s of oil having a sg=0.8 occurs through the venturi shown. The diameter of the pipe is 37.5 mm while that of the throat is 25 mm. The liquid in the differential gage shown contains mercury sg = 13.6 and the rest is filled with oil 37.5 mm A) Find the velocity at the throat (7.7 m/s) B) Compute for the value of h1 (0.8125 m) C) Compute for the value of h2 (0.238 m) oil mercury 25 mm h1 37.5 mm h2