2- Oil (p = 80o kg/m3) flow through a 5omm-diameter smooth pipe at a velocity of 2m/s, the pressure drop due to friction loss in the pipe 5023 pa. The pipe length is 1om. a- Calculate the friction factor, f. %3D b- Determine whether the flow is laminar or turbulent. C- Calculate the oil viscosity. (b) o.0157 (d) 487x10-6 N s/m2]

2- Oil (p = 80o kg/m3) flow through a 5omm-diameter smooth pipe at a velocity of 2m/s, the pressure drop due to friction loss in the pipe 5023 pa. The pipe length is 1om. a- Calculate the friction factor, f. %3D b- Determine whether the flow is laminar or turbulent. C- Calculate the oil viscosity. (b) o.0157 (d) 487x10-6 N s/m2]

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Tank shown in figure below is one side open to the atmosphere and the other side sealed with air above the oil. The oil has sp.gr. of 0.90. Calculate the gage pressure at points A, B, C, D, E and F and the air pressure in the right side of the tank. [FILL THE TABLE BELOW AND SH OW YOUR WORK NEAT & CLEAR] Air Absolute F Gage Pressure (KPa) Pressure Point (psi) 1.5 m E 3.0 m Oil D E 3.0 m F
Q2: A flocculation tank with a discharge of 50,000 m³/day and alum dosage is 50 mg/1, Gt=4*104 at a temperature of 15 °C. This tank contains three paddles, each paddle has two boards with a dimension of 5m length, rotational speed is 2.5 rpm, and velocity gradient is 30 s¹. The distance between the center of the board and the shaft is 1.25m find: 1)Design this tank if the depth equal one-third of width, assuming depth according to design criteria of flocculation tank 2)Power required Width of the paddles?
Air is flowing from a reservoir through a long, insulated, isentropic nozzle. The pressure and temperature at the reservoir are 15 atm and 950 K, respectively. The Mach number at the entrance of the pipe is 0.05. Determine the maximum allowable length of the pipe. Assume that the inside of the pipe is smooth.
O -0.13 Darcy Experiment A set-up of Darcy Experiment involves measuring the pressure head at two piezometers separated a distance, L. Given the set-up shown, determine the hydraulic gradient if the hydraulic head at (1) is 24 inches, hydraulic head at (2) is 11 inches, and the travel distance is 100 inches. O 7.7 O -7.7 (1) O 0.13 e - - - -
A cylindrical tank contains water at a height of 55mm as shown. Inside is a small open cylindrical tank containing cleaning fluid (s.g.-0.8) at a height h. The pressure Pb-13.4 kPa gage and Pc-13.42 kPa gage. Assume the cleaning fluid is prevented from moving to the top of the tank. (a) Determine the pressure Pa in kPa, (b) the value of h in mm, and (c) the value of y in millimeters
Compute the pressure @ point n ( Pn ) as shown by the differential manometer in KPa if pressure @ point m ( Pm ) is equal 1027.66 mm Hg. air plpeline where: a= 12" b=3,2 C-4.0 d- 12 m mercury density (16 300 kghm) water pipeline
plzzzz help meee right nowww plzzz what will be the pressure gradient (kpa/m) at L=30 cm through the nozzle? At L=0, the liquid flows inside the nozzle has a specific gravity S=7.5, at L=0, the velocity is 2 m/s while at L=70 cm, the velocity is 6 m/s. Assume steady and inviscid flow. The velocity varies linearly with distance through the nozzle
Please help
a&b answer
IL. Q2-1 [5 Points]:A fluid has an absolute viscosity of 0.048 Pa-s and a specific gravity of 0.913. For flow of such a fluid over a solid flat surface, the velocity at a point 50 mm away from the surface is 1.467 m/s. Calculate the shear stresses at the solid boundary (N/m) 0.67 1.2 3.35 0.97 1.41 3.03 1.35 1.79
Problem 10.56 The 100-mm-diameter commercial steel pipe discharges water at 25°C through the 40-mm-diameter nozzle. (Figure 1) Figure 40 mm g 60e 3m A 100 mm 1 of 1 Part A If the pressure at A is 250 kPa, determine the discharge. The minor loss coefficient of the nozzle is KL = 0.15. Express your answer to three significant figures and include the appropriate units. Q= Submit OL μА Value Provide Feedback Request Answer Units ? (v 5 of 6 Review Next >
Calculate the Oil's Flow rate from the nozzle and the pressure at point A, B and D