A weight W= 120 kN is being supported by steel sections with force T, force F, and force C. The coordinates of A, B, C, and D are given. Assume that E is the origin (0,0,0). Determine Forces T, F, and C. aGO C一一245 m 1.25 m క్తం A 1.85 m 1.22 m 0.90 Wa120 KN

Q: Differentiate and discuss the common hardness testing methods

A: Hardness testing: - It is defined as a non-destructive test method which is used to determine…

Q: Concrete Hollow Block 200mm H x 400mm Lx 150mm thick per piece and Laying 4 layers x 4 meters…

A: "Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Handwritten/ neat work pls show the steps on how u got the areas and not just the answers. Parts d,…

A: A framing plan is given we need to find out the tributory areas

Q: 8.4 The concrete block shown has wall thicknesses of 40 mm, voids that are 95 mm x 110 mm, and is…

A: The center of the thing is represented by its centroid. The centroid of a triangle is the location…

Q: What is the Liquid requirement rate in perforated plate scrubbers?

A: The liquid requirement rate or Liquid to gas ratio is the volume of liquid injected per volume of…

Q: To be classified as a tile, a unit must have what percentage voids?

A: option B is correct

Q: Q10: The following values were found from the corrected load versus penetration curve Satisfactory…

A:

Q: 10. a) Find the concrete volume of a 30 ft x 15 ft x 12 in concrete slab. b) Calculate steel…

A:

Q: Weight Retained 1.570 kg 1.554 kg 2.570 kg 1.84 kg 2.223 kg 0.22 kg 0.023 kg Sieve No. Cum. Weight…

A:

Q: answer with short

A: The solder was disturbed while cooling, or has overheated in operation to the paste phase and so…

Q: Is the inspector reponsible to reject the faulty materials?

A: An inspector presents complete on-site observations to the engineer to control the materials,…

Q: Briefly describe Mix Columns

A: To describe Mix columns

Q: Find the centroid of given composite figure. Set- up the reference axis on the lower left corner.…

A: Centroid about x-coordinate :x¯=A1x1+A2x2+A3x3A1+A2+A3

Q: How did you determine its a smooth pipe?

A: Given data: εd=9.87×10-5Nd=944,444.44

Q: What should be the name of the layer shown as " purple ?" As a numerical calculation, the fault line…

A: We will solve this question in step no. 2

Q: the load is 150kN at the center of the beam and the dimension of the beam is 6x6x24. compute for…

A: P=150kN L=24 b=6 h=6

Q: Determine

A: The minimum area if shrinkage bars is given by 0.12% of gross area of slab.

Q: efine the term crevice which is one form of corrosion.

A: Crevice corrosion refers to the attack of metal surfaces by a stagnant solution in crevices, for…

Q: Q1: Why Iraqi specification no. 5 limited max. SO3 by 2.5% when C3A !7%. *

A: Brief concept introduction- Iraqi Specifications No. (5), 1984 for Portland Cement.- Iraqi…

Q: Describe the sieve analysis.

A: A sieve analysis is an analytical method that is used to define the particle size distribution of…

Q: Prepare a complete NC program for finishing profile shown in fig.2 with continuous cut in clockwise…

A:

Q: epare a datasheet and calculate the cost of plastering cement (1:5), 20mm thick for 50m². Also…

A: Given data:- Ratio of plastering cement is 1:5 Thickness of plaster is 20 mm Area of plastering is…

Q: Make a tabulated Data .  Brand A ( pozzolan Mabuhay Brand - make a remarks either Good condition or…

A: Solution: The Republic cement Provides high quality products of cement that are very consistent for…

Q: What is the thickness of Branch canal lining? * O 100 mm O 50 mm 80 mm

A: thickness of branch canal lining is mostly 50mm .

Q: sieve analysis what's the meaning or gonna happen if the So is zero

A: A sieve test is generally called as gradation test, is one of the most important and widely used…

Q: What is the main working member of a grader? Oa. Moldboard O6.0perator Oc. Large tires. Oa.Engine

A: Grader is a heavy machine which used in the road construction .

Q: A sieve analysis test was performed on a sample of coarse aggregate and pro- duced the results in…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Differentiate porosity, permeabiloity, water saturation and resistivity properties. What…

A: Solution: Porosity: It is defined as the property of loose sediments, rocks, or soil to hold fluid…

Q: Provide clear and step by step solution Using LRFD, PL400x350 mm base plate, W12x120 column,…

A:

Q: On Autocad, what is the difference between polyline and line?

A: The major difference between Line and Polyline(PLine) , That the line command, fetches the line…

Q: PLACE YOUR ANSWERS HERE. Ix= ly= r₂ = Ty= 4"x6"X" 10" 12" 4"X 8"X1" X

A: rx = (Ix/A)0.5

Q: is 55 HRC (hardness test) good? explain

A: Yes, 55 HRC is good. Let us take an example of kitchen knife here for hardness. What actually…

Q: Describe about the Flat-blade dilatometer testing.

A: The Flat Dilatometer Test:

Q: (i) Determine the angle of threaded screw, 0. (ii) Find the angle on static friction, Øs. (iii)…

A: Given Data: The pull effort is given as P=25.9 N. The mass of a block is m=100 kg. The diameter of…

Q: How are the specimens supported and loaded in each?

A: This question is related to the Solid Mechanics from Civil Engineering. In this question , ask about…

Q: Derive the "bulk density" and "voids" formulas?

A:

Types of Cement

Cement is a fine mixture of limestone, chalk, or marl and clay which when mixed with water, becomes compacted due to the formation of strong molecular bonds. Due to hydration, cement turns into a hard mass when left for a sufficient amount of time upon mixing with water. The water turns the cement compounds into gel-like submicroscopic particles having higher surface areas. It is due to the hydration properties of cement, they are often known as hydraulic cement. For instance, Portland cement is a popular example in this category.