A water sample that is believed to contain a maximum hardness of 100.0 ppm CaCO₃ was titrated with 0.002101 M EDTA. What volume of EDTA is needed for the titration if the water sample used was 25.00 mL? (The molar mass of CaCO₃ is 100.087 mg/mmol)

Q: A student titrates 20.0 mL of solution of Mg(OH)2 with 0.0420 M EDTA. The initial buret reading was…

A: Mole of EDTA added is approximately 6.17 x 10-4 mol

Q: If in procedure B analysis of Zn2+ alone, 8.55 mL of 0.0100 M EDTA solution is used to fully titrate…

A: Given: Volume of EDTA =8.55 mL Concentration of EDTA = 0.0100 M To determine: i) mmol of Zn2+

Q: Calculate the concentration of an unknown solution if the titration used 4.6 mL of DCPIP solution to…

A: Introduction: A titration is a method used to find the unknown concentration of the solution from…

Q: 3) After neutralizing a 50 mL water sample, pH 10 buffer and Erio-T indicator are added. Then 6.1 mL…

A:

Q: A 50.00 ml aliquot of a solution containing Ca2+ and Mg2+ was buffered at pH 10 and titrated with…

A: The objective of the question is to calculate the molar concentration of Mg2+ in a solution. This…

Q: In order to adjust the EDTA solution, 10 mL of 0.01M Ca + 2 sample was taken and 10 mL of pH 10…

A: Ca2+ ions forms a complex compound with EDTA ligand. One mole of Ca2+ inos form complex with one…

Q: Two 25.0-mL solutions of 0.100 M Ba²+ are titrated with 0.100 M EDTA at pH 10. Calculate the value…

A:

Q: After preparing the citrate buffer, Vegas and Pete determined the buffer capacity of the solution by…

A: A question based on quantitative analysis. A set of data about volumetric titration is prescribed…

Q: A 15.00 mL urine specimen containing Ca2+ and Mg2+ was diluted to 2.000 L. A 10.00 mL sample was…

A:

Q: The concentration of CA2+ in an unknown solution was determined by titration with the EDTA solution…

A: Molarity of EDTA solution = 0.000085 M Volume of EDTA solution = 35.54 mL Volume of the diluted…

Q: A 49.10 mL aliquot from a 0.500 L solution that contains 0.530 g of MnSO4 (MW=151.00 g/mol) required…

A: Solution -

Q: titration of 50.00 mL of 0.1100 M Fe3+ with 0.07750 M Sn2+ is carried out. The analytical reaction…

A:

Q: A 30-mL portion of a solution containing Ca2+ and Mg2+ was titrated with 28.19 mL of 0.213 M EDTA at…

A: Complexometric titration with EDTA is used for the determination of metal ions line calsium and…

Q: Consider the titration of 27.00 mL of 0.100 M HNO3 with 0.0900 M KOH. Calculate the pH at the…

A: Reaction between HNO3 and KOH is neutralization reaction where H+ and OH- neutralises each other and…

Q: An unknown Ca solution was prepared by weighing a 2.122 g sample, dissolving it in HCl and then…

A:

Q: a 20 mL of EDTA titrant is required to titrate 40 mL of standard 0,25M CaCO3. A 70 mL hard water…

A:

Q: In the titration of 25.00 mL of a water sample, it took 20.690 mL of 4.050x 10−3 M EDTA solution to…

A: Number of moles of EDTA is determined as follows,

Q: which of the following is the concentration of the EDTA solution in terms of molarity?

A: Ca2+ forms a complex compound with EDTA ligand. EDTA is a hexadentate ligand. Onle mole of Ca2+…

Q: A 1.000 mL aliquot of a solution containing Cu²+ and Ni²+ is treated with 25.00 mL of a 0.03703 M…

A: The objective of the question is to find out the volume of 0.02138 M Zn²+ required for the back…

Q: A sample of water from a river was analyzed by titrating a 125 mL aliquot with 0.0210 M EDTA,…

A: EDTA reacts with Ca in 1:1 ratio to form CaEDTA complex. By using definite concentration of EDTA ,…

Q: Titration of 0.2121 g of primary standard Na C,0, (133.999 g/mol) required 21.66 mL of KMnO,…

A: Given that:  Mass of Na2C2O4 = 0.2121g Molar mass of Na2C2O4 = 133.999g/mol Moles of Na2C2O4 =…

Q: A 1.000 mL aliquot of a solution containing Cu²+ and Ni²+ is treated with 25.00 mL of a 0.03703 M…

A: Given,Concentration of EDTA = 0.03703 M

Q: 4.50 mL of 0.1 M Ca2+ ion was titrated at pH 10 with 0.1 M EDTA. What will be the concentration of…

A:

Q: 3 M during the titration.

A: Given - 1] Water = 200 mL  2] Sulfuric acid = 20mL 3] Phosphoric acid = 5 mL 4] Potasium Dichromate…

Q: 50.00 mL of a solution containing both Ni2* and Pb²+ ions requires 46.32 ml of a 0.02041 M EDTA…

A:

Q: Titration of 25.0 mL of a 0.0500 M Zn2+ solution with 0.0550 M EDTA in a solution buffered at pH 8.…

A: Conditional formation Constant, Kf’ can be determined as follows: where Kf is the formation…

Q: Hu Hd 12 10 8 6 4 2 0 0 4 8 12 16 20 24 28 32 36 Volume Base Added (mL) 8A. What was in the…

A: A titrant is the solution which is added from burette while a sample is taken in titration flask.In…

Q: Which one of the following indicators would be best to use when titrating 0.1M morphine (Kb = 1.6 ×…

A: pH is a measure of hydrogen ion concentration in solution and it measures acidity or alkalinity of a…

Q: Titration of 0.2121 g of primary standard NagC;0, Calculate the molar concentration of KMnO,? 2…

A:

Q: Titration of Ca 2+ and Mg 2+ in a 50.00 mL sample required 25.50 mL Of 0.01115 M EDTA. A second 50…

A:

Q: In a precipitation titration, a 50.0 mL of 0.100 M NaCl was titrated with a standard solution of…

A: The reaction between NaCl and AgNO3 is- NaCl (aq)+ AgNO3 (aq)→AgCl (s) + NaNO3 (aq)

Q: You titrate 50.00 mL of hard water with 14.86 mL of 0.0100 M EDTA solution. How many moles of Ca²+…

A:

Q: Consider the titration of 27.00 mL of 0.100 M HNO3 with 0.0900 M KOH. Calculate the pH at the…

A: As titrant required to achieve end point of the titration is = 30 ml . Before 30 ml of ritrant is…

Q: Sample of calcium was buffered to pH 10 prior to analysis. A 25 mL urine sample required 17.25 ml of…

A: The analysis of calcium and magnesium in the urine sanple is done using complexometric titration…

Q: 50 mL of a sample known to contain Mg+2 was taken and titrated with 0.075 M EDTA standard solution…

A: We have given that Molarity of EDTA = 0.075M Volume of EDTA used = 10.5mL Volume of sample taken =…

Q: A 25.00 mL sample of water, buffered at a pH of 10, is titrated with 0.008989 M EDTA using the…

A: The hardness in water can be calculated using EDTA which binds with metal ions like Ca and Mg.

Q: A 47.90 mL aliquot from a 0.500 L solution that contains 0.480 g of MnSO4 (MW= 151.00 g/mol)…

A: The objective of the question is to determine the mass of calcium carbonate.

Q: Titration of Ca²⁺ and Mg²⁺ in a 50.0 mL sample of hard water required 32.45 mL of 0.01162 M EDTA. A…

A: A question based on mole concept that is to be accomplished.

Q: 50 mL of a sample known to contain Mg+2 was taken and titrated with 0.075 M EDTA standard solution…

A: Magnesium solution is titrated complexometrically with a standard EDTA solution. we need to…

Q: A 30-mL portion of a solution containing Ca²+ and Mg2+ was titrated with 28.19 mL of 0.207 M EDTA at…

A: Given that, In the first titration Volume of Ca-Mg solution = 30 mL Volume of EDTA used = 28.19 mL…

Q: 12 10 8 Hd Ho 6 2 0 0 4 8 12 16 20 24 28 32 32 36 Volume Base Added (mL) 8A. What was in the…

A: An equivalence point is the point where all the acid has been neutralised by adding base.

Q: What is the mass of pure dry CaCO3 (MW: 100.0869 g/mol) standard used in the standardization of EDTA…

A: A question based on mole concept that is to be accomplished.

Q: Consider the titration of 150.0 mL of a 0.225 M solution of (C2H5)NH with 0.45 M HCl(aq).  Kb= 4.3…

A: (C2H5)2NH is a weak base with Kb = 4.3*10-4. HCl is a strong acid. Hence (C2H5)2NH and HCl will…

Q: what is the value of magnesium in ppm in the sample?(Mg:24 g/mol)

A: The titration reaction is: Mg2+ + EDTA-4 ====> Mg(EDTA)-2 Let us first calculate moles of EDTA…

Q: The Telluride ion was determined by indirect titration with EDTA. To a solution conta 50.00 mL of…

A: Given Concentration of Zn(ClO4)2= 0.08664 M Given Telluride Solutions = 50 ml We have to calculate…