A) Water at 70 °C flows up a 50-ft-long conical pipe with its centerline sloping at 5° to the horizontal, as shown in figure (1). At its lower end the diameter is 24 in, the water pressure is 15 psi; at its upper; outlet end the diameter is 18 in and the water pressure is 12.5 psi. By a method, the shear stress found to be 0.25 b/ft². Assuming this value to be non-varying, calculate the flow rate. given = 62.30 lb/ft³. 18 in dia so fr 12.6 p 24 in dia 2₂-0.25 16/4²

A) Water at 70 °C flows up a 50-ft-long conical pipe with its centerline sloping at 5° to the horizontal, as shown in figure (1). At its lower end the diameter is 24 in, the water pressure is 15 psi; at its upper; outlet end the diameter is 18 in and the water pressure is 12.5 psi. By a method, the shear stress found to be 0.25 b/ft². Assuming this value to be non-varying, calculate the flow rate. given = 62.30 lb/ft³. 18 in dia so fr 12.6 p 24 in dia 2₂-0.25 16/4²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What’s the answer for this please ?
2) For the same system of question 1, let Az = 80 m and L pipe diameter for which the flow rate will be 7 m³/h? = 185 m of cast-iron pipe. What is the
Question 3 Water (p = 1000 kg/m³, μ = 1.12 x 10-3 Ns/ m²) flows through a 0.01-m-diameter pipe at a velocity of 2 m/s. The length of the pipe is 40 m. A pump is used to maintain the flow from one reservoir to another reservoir as shown. The following data are available: KL elbow = 1.5, Kentrance = 0.5, Kexit = 1.0. Elbow Pump Elbow Figure Q1 Note that the entrance and exit are at the same elevation. The free surfaces of the reservoirs are also at the same elevation. (a) Calculate the total head losses in the pipe.
The water is delivered with piping system given in the figure below. The levation difference between entering section and tank is 143,55 m. Estimate the gage pressure [MPa] at point 1. (Note: For water at 20°C, take p=998 kg/m and u=0.001 kg/ms. ) 5 cm diameter cast-iron pipe Length of the system is 1.2 km All fittings are flanged. The vohume flow rate is 300 L min 45 treaded elbow Yanit
The square-section duct in atmospheric conditions is exposed to outside air flow as seen in the figure. The temperature of the air is T air= 5°C, the velocity is V air= 10m/s. Find the exit temperature of the water entering the channel at a flow rate of ṁwater=0.01 kg/s and a temperature of T water,g=50°C. Geometric dimensions are given on the figure.
Oil (SG = 0.84) is flowing in a pipe under the conditions shown in Figure. Find the pressure at point 2
Parvinbhai
In a fully developed turbulent flow through a pipe, the shear stress is……… Please fill the blank correctly.
The pressure drop in a horizontal commercial steel pipe should not exceed 1 psi per 150 feet of pipe length for flow rates up to 500 gal/min. If the water temperature is never below 50 F°, determine the necessary pipe diameter.
A fluid is flowing from small diameter
Water at 80°F flows from a storage tank through 618 ft of 6-in Schedule 40 steel pipe, as shown in the figure. Taking the energy loss due to friction into account, calculate the required head hin feet above the pipe inlet to produce a volume flow rate of 1.65 ft³/s. (round the final answer to three significant figures) h 6-in Schedule 40 steel pipe pipe length
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. What is the value of G in kg/s.m2?. (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol