QUESTION 3In an olive oil process plant, eight thin steel baffle plates are to be installed in arectangular conduit to serve as flow straighteners as indicated in figure 3. The olive oilflow through the conduit and baffle plates. The Reynolds number at the inlet to thebaffle plates is 4000.3.13.23.3Ubh3ahb = 225 mmh = 150 mmw = 130 mmProperties of olive oil:Dynamic viscosity: 0.08 Pa.sDensity: 841.8 kg/m³bFigure 3Determine the free stream velocity (U) at the baffle inlet and the volumetric flowrate. It is required that the boundary layer must be laminar across the baffleplates. Determine if it will be the case.Calculate the boundary layer thickness at the leading edge, center, and trailingedge of the baffle plate.Calculate the displacement thickness at the trailing edge and determine thecorresponding free stream velocity.

Name: QUESTION 3In an olive oil process plant, eight thin steel baffle plat
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: QUESTION 3In an olive oil process plant, eight thin steel baffle plates are to be installed in arectangular conduit to serve as flow straighteners as indicated in figure 3. The olive oilflow through the conduit and baffle plates. The Reynolds number

Answered: Image /qna-images/answer/b6533ab2-7af9-4c4f-a0bb-bdfdf8bdfdf4.jpg

Engineering

Mechanical Engineering

In an olive oil process plant, eight thin steel baffle plates are to be installed in a rectangular conduit to serve as flow straighteners as indicated in figure 3. The olive oil flow through the conduit and baffle plates. The Reynolds number at the inlet to the baffle plates is 4000. 3.1 3.2 3.3 U b h W h b = 225 mm h = 150 mm w = 130 mm Properties of olive oil: Dynamic viscosity: 0.08 Pa.s Density: 841.8 kg/m³ Figure 3 Determine the free stream velocity (U) at the baffle inlet and the volumetric flow rate. It is required that the boundary layer must be laminar across the baffle plates. Determine if it will be the case. Calculate the boundary layer thickness at the leading edge, center, and trailing edge of the baffle plate. Calculate the displacement thickness at the trailing edge and determine the corresponding free stream velocity.

In an olive oil process plant, eight thin steel baffle plates are to be installed in a rectangular conduit to serve as flow straighteners as indicated in figure 3. The olive oil flow through the conduit and baffle plates. The Reynolds number at the inlet to the baffle plates is 4000. 3.1 3.2 3.3 U b h W h b = 225 mm h = 150 mm w = 130 mm Properties of olive oil: Dynamic viscosity: 0.08 Pa.s Density: 841.8 kg/m³ Figure 3 Determine the free stream velocity (U) at the baffle inlet and the volumetric flow rate. It is required that the boundary layer must be laminar across the baffle plates. Determine if it will be the case. Calculate the boundary layer thickness at the leading edge, center, and trailing edge of the baffle plate. Calculate the displacement thickness at the trailing edge and determine the corresponding free stream velocity.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ANSWER ASAP PLS
A Process fluid is pumped from the bottom of one distillation column to another, using a centrifugal pump. The line is a standard commercial steel pipe with a 75 mm internal diameter. From the column to the pump inlet the line is 25 m long and contains six standard elbows and a fully open gate valve From the pump outlet to the second column, the line is 250 m long and contains ten standard elbows, and four gate valves (operated fully open). The fluid level in the first column is 4 m above the pump inlet. The feed point of the second column is 6 m above the pump inlet. The operating pressure in the first column is 1.05 bara and that of the second column is 0.3 barg. (i) Draw the system, (ii) determine the operating point on the pump characteristic curve. (iii) determine the NPSH at this flowrate. The physical properties of the fluid are: density 875 kg/m³, viscosity 1.46 mNs.m², and vapour pressure of the fluid at the pump suction is 25 kN/m². Kelbow-0.75, Kvalve 0.17. Flow rate, m³/h…
x
QUESTION 1 Figure 1 shows water at 20°C to be circulated from and to the reservoir. The 30 mm diameter pipe made of commercial steel, 60 m long is to be used. Water will be pumped by a 65% efficient motor-pump combination that draws 400 W of electric power during operation. Estimate the total volume flow rate through the valve. KL exit = 1.0 KL elbow = 1.5 KL = 0.8 KL Filter KL valve 6.0 = 12.0 filter H Pump Figure 1 Lent
Example -5.2- It is required to pump cooling water from storage pond to a condenser in a process plant situated 10 m above the level of the pond. 200 m of 74.2 mm i.d. pipe is available and the pump has the characteristics given below. The head loss in the condenser is equivalent to 16 velocity heads based on the flow in the 74.2 mm pipe. If the friction factor = 0.003, estimate the rate of flow and the power to be supplied to the pump assuming n = 0.5 Q (m³/s) 0.0028 0.0039 0.005 0.0056 0.0059 Ah (m) 23.2 21.3 18.9 15.2 11.0
REFERENCE: FROM BOOK - ENGINEERING THERMOFLUIDS, M. MASSOUD
6. SAE 10 oil is being released from a main reservoir to a smaller reservoir. The pipeline consists of 100 m of 100 mm diameter wrought iron piping. A fully open globe valve, three standard 90° elbows and two standard 45° bends are used as shown in Figure 2. The pipeline has square entrance and exit and all fittings are screw-connected. The discharge is 50 L/s. The density and dynamic viscosity of oil are 869 kg/m³ and 0.0814 Ns/m² respectively. Determine the total head loss in the pipeline. Answer (103.29 m of oil) A Globe valve B Figure 2 E
Can You Solve This.
Refrigeration
3. A pump steadily circulates oil used for lubricating heavy machine tools. The volume flow rate and temperature of the oil are 300 gal/min and 104°F, respectively. At 104°F, the kinematic viscosity and the specific gravity of the oil are 2.15 x 10-3 ft² /s and 0.89, respectively. The pipe lengths are 25 ft for the 4-in diameter pipe and 75 ft for the 3-in diameter one. The Schedule-40 steel pipe has an average roughness element size of 0.0018 in. If all minor losses can be ignored, evaluate how much power (in a unit of horsepower) the pump delivers to the oil. 6 ft 22 ft Flow 15 ft Discharge line 3-in Schedule 40 Suction line 4-in Schedule 40 steel pipe steel pipe Pump
From THERMOFLUIDS, M. MASSOUD Please hep me solve this problem i will really appreciate it
C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the pipeline. The velocity at the smaller end is 4.9 m/s and at the larger end is 2.5 m/s. The length of the conical tube is 1.3 m and the flow rate of the water is 127 liters/s. The pressure at the smaller end is equivalent to a head of 10.1 m of water. Considering the following two cases: (1) Neglecting friction, (without head loss) determine (i) the diameter at the smaller end in meter, (ii) the diameter at the larger end in meter, and (ii) the pressure at the larger end of the tube in m of water. (2) If a head loss (with head loss)in the tube,h = 0.0153(V1-V2)2, where V1 is the velocity at the smaller end and V2 is the velocity at the larger end, determine (iv) the head loss in m of water and (v) the pressure at the larger end of the tube in m of water. 6) the diameter at the smaller end in meter (ii) the diameter at the larger end in meter (iii) the pressure head at the larger end of the…