Corection the following number k=.02625,Kinematic viscosity(fancy v)=16.55*10^-6m^2/s,Pr=.7 Re(x=L)=54380 Nu(x)=170.1 h(x=L)=29.8 Ts(1)=54.9C Find out the total convective heat transfer rate from the board in Example 2B.2 (solve the bolded part) Example 2B.2: A 15-cm by 15-cm circuit board is being cooled by air. It is dissipating 890 W/m² of heat to the air from its top surface. The air approaches the circuit board at 25 °C with a velocity of 6 m/s. Determine the surface temperature of the circuit board at the end of the board. Assume the flow to be turbulent at the leading edge of the board since the electronic components are expected to act as turbulators. For air properties evaluations assume a film temperature of 35 °C. Given: Circuit board geometry – length, L = 0.15 m, width, W = 0.15 m Convective heat flux to air, q" = 890 W/m² %3D Free-stream temp., T = 25 °C. Free-stream velocity, U, = 6 m/s %3D Assumption: Steady state. Only mode of heat transfer from the board is convection. Film temperature is T¡ = 35°C. Properties are considered constant and uniform. Flow is turbulent. Air is an ideal gas. Properties: Air properties at 35°C: k = 0.0265 W/m°C; v = 16.5×10- m²/s; Pr = 0.7 %3D

Corection the following number k=.02625,Kinematic viscosity(fancy v)=16.55*10^-6m^2/s,Pr=.7 Re(x=L)=54380 Nu(x)=170.1 h(x=L)=29.8 Ts(1)=54.9C Find out the total convective heat transfer rate from the board in Example 2B.2 (solve the bolded part) Example 2B.2: A 15-cm by 15-cm circuit board is being cooled by air. It is dissipating 890 W/m² of heat to the air from its top surface. The air approaches the circuit board at 25 °C with a velocity of 6 m/s. Determine the surface temperature of the circuit board at the end of the board. Assume the flow to be turbulent at the leading edge of the board since the electronic components are expected to act as turbulators. For air properties evaluations assume a film temperature of 35 °C. Given: Circuit board geometry – length, L = 0.15 m, width, W = 0.15 m Convective heat flux to air, q" = 890 W/m² %3D Free-stream temp., T = 25 °C. Free-stream velocity, U, = 6 m/s %3D Assumption: Steady state. Only mode of heat transfer from the board is convection. Film temperature is T¡ = 35°C. Properties are considered constant and uniform. Flow is turbulent. Air is an ideal gas. Properties: Air properties at 35°C: k = 0.0265 W/m°C; v = 16.5×10- m²/s; Pr = 0.7 %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

n = Xe()r -------Equation 1 where X = 1.7419 and (E/R) = -0.018 are constants for a given fluid. You are required to carry out appropriate calculations on the effect of changes in temperature given in table A by using equation 1 for Ethanol on the viscosity of a fluid. Table A NO Temperature viscocity n T°C cP 10 3 20 30 5 40 6. 50 7 60 8 70 In addition to this, calculate other constraints such as the variety of shear stress (T) and force due to fluid viscosity, when the two layers of different compressible Newtonian fluids are contained between two flat plates separated by a distance of 0.05m and fluid moving with the velocity of 2m/s in the horizontal direction. Assume the shear area between the fluid layers is 0.5m². To do this you required to explain, with examples, the effects of temperature and shear forces on Newtonian and non-Newtonian fluid. Also, explain the operation and constraints of different viscometers that quantify viscosity in fluids. 2.
Question 1: Define and state the viscosity equation for a Coutte flow. Question 2: Develop and algebraic equation for viscosity of a liquid as a function of temperature. Calculate the kinematic viscosity of water at T = 303 K. Question 3: If a liquid water at 300C is flowing in a pipe and the pressure drops to the vapor pressure, what happens in the water and why, explain?
I want the method to calculate the Reynolds number, where did this number 435,000 come from(Marked in red) ? please very urgent
% ParametersD = 0.1; % Diameter of the tube (m)L = 1.0; % Length of the tube bundle (m)N = 8; % Number of tubes in the bundleU = 1.0; % Inlet velocity (m/s)rho = 1.2; % Density of the fluid (kg/m^3)mu = 0.01; % Dynamic viscosity of the fluid (Pa.s) % Define the grid size and time stepdx = D/10; % Spatial step size (m)dy = L/10; % Spatial step size (m)dt = 0.01; % Time step size (s) % Calculate the number of grid points in each directionnx = ceil(D/dx) + 1;ny = ceil(L/dy) + 1; % Create the velocity matrixU_matrix = U * ones(nx, ny); % Perform the iterationsfor iter = 1:100 % Calculate the velocity gradients dUdx = (U_matrix(:, 2:end) - U_matrix(:, 1:end-1)) / dx; dUdy = (U_matrix(2:end, :) - U_matrix(1:end-1, :)) / dy; % Calculate the pressure gradients dpdx = -mu * dUdx; dpdy = -mu * dUdy; % Calculate the change in velocity dU = dt * (dpdx / rho); % Update the velocity matrix U_matrix(:, 2:end-1) = U_matrix(:, 2:end-1) + dU; % Apply…
Fluid Mechanics
f. A study of the physical characteristic of honey was conducted due to the large demand of royal jelly. A capillary tube viscometer was used by a researcher in determining the viscosity of the honey. The viscometer is 250 mm long with an outside diameter of 55mm and effective thickness of 2.5mm and was used horizontally so that the effect of gravity was neglected. At an ambient temperature of 30°C the following data were collected: Q (cc/s) 1.25 1.55 1.80 2.05 ДР (Ра) 10.0 12.5 15 17.5 20.0 2.55 What will be the stress produced per unit length in the tube used in the production of royal jelly if it has a radius of 5mm and a flow of 1 capsule per second. (1 capsule = 0.85 cc of royal jelly).
Please answer the following question
Please solve correctly, Show unit conversion (I don't know why there is conversion factor 1488 in the numerator)
What is the dynamic viscosity of the fluid? must include FBD F ... F = 0.45 Ibf m = 151 g v = 0.006 m/s Thk. = 20 cm THISE AN 8mm 6mm, A Steel Plate is pulled up at a constant QU velocity between two layers of liquid 30 cm Ignore Friction at openings @ 20°C @ 20°C 1940
The viscosity of motor oil is 4.79× 10-³ N. s/m², motor oil is used as a lubricant between two machine parts. The variation in velocity of the oil is 1.6 m/s and a maximum shear stress is 62.8 N/m². What is the required spacing between machine parts in millimeter?
Answer fast will like
CHAPTER 3 - 6 BOOK: FLUID MECH & THERMODYNAMICS, 6e, S.L. Dixon, C.A. Hall (The answer is available in Chegg, but I don't have an account for that. Thanks)