A voltage regulator is shown in Figure 6. Solve the following :(i)Explain the function of the comparator and the voltage divider in thecircuit.(ii)Determine the output voltage of the voltage regulator if R;= 10 k,R2 = 5.6 kQ, R = 2.2 kQ and zener voltage = 2.2 V.(iii) Explain the changes of output voltage if R3 is 5.0 ko.+12 Vo-Figure 6

The voltage regulator is a circuit used to regulate the supply of voltage to the external devices.

A voltage regulator is shown in Figure 6. Solve the following : ) Explain the function of the comparator and the voltage divider in the circuit. (i) Determine the output voltage of the voltage regulator if R;= 10 kQ, R2 = 5.6 ka, R3 = 2.2 kQ and zener voltage = 2.2 V. (ii) Explain the changes of output voltage if R3 is 5.0 kn.

A voltage regulator is shown in Figure 6. Solve the following : ) Explain the function of the comparator and the voltage divider in the circuit. (i) Determine the output voltage of the voltage regulator if R;= 10 kQ, R2 = 5.6 ka, R3 = 2.2 kQ and zener voltage = 2.2 V. (ii) Explain the changes of output voltage if R3 is 5.0 kn.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

half bridge given in the figure for the rectifier circuit; Output current and voltage waveform draw
Design a bias stable circuit in the form of figure 2 to operate at Ico =0.8 mA, VCEQ = 4 V, and VR. = 0.7V. Given B = 120. Vec = 10 V Ca R-I ka CE Figure 2 tww -ww
A 500 ohm resistor is connected to a 12V source at one terminal and a 10V zener diode of 250 mW and a 5K ohm resistor are connected to the other terminal. What is the maximum current of the zener diode?
Calculate the dc and ac components of the output signal across load RL in the circuit of Figure * Va = 150 V V, (ms) = 15 V V's V', (ms) R 500 2 Full-wave rectifier C, 15 μF C2 10µF RL 5 ka O vdc= 136.4V, Vac= 3.9V O Vdc= 163.4V, Vac= 9.3V Vdc= 13.4V, Vac= 9.9V O None of the above
32 Basic Zener Regulation Past If the input voltage, Vi = 40 V, the zener diode voltage Vz = 15 V, R = 1002, load resistance is 802, and Pzm = 1 W. The following statements are true except, * load voltage is exactly the same as Vz load voltage is greater than Vz Power delivered by the input voltage is 10 Watts power dissipation of R = 6.25 Watts IN+ R₂
The power dissipated by the zener diode for the circuit of Figure is greatest when: (a) The zener diode is shorted. (b) The load resistor is removed. (c) The load resistor is shorted. (d) The input voltage is increased.
The output for the following clamping circuit is shown below assuming ideal diode calculate the avarege value and r.m.s value for the output circuit Vm-10. V=5 R (1) Figure 7-2 simple parallel clippers (Ideal diodes) (7-3)
-8V R=1.2k2 R2= 2-5kS2 Silicon diode Construct the circuit in more easy wawy and kindly solve the following thank you withexplanation pleare Diode condition * current * Diode Current Diode voltage (Vo) Output voltage ( V5)
N
Draw the circuit generation of direct current Doubler circuit by put another stage (3 Stages)
Could you please help me in this question?
Please show work, thanks :)