In the circuit below, when a 2.2KN load is connected to the output, find the value of the currentflowing through the R resistor (IR), the current passing through the zener diode (Iz) and the loadcurrent value (IL).SigortaT1Dr-De 1N40010,1AREGOLATORD220VACVa-20VVsACVa2200DeVi-13V15V4700uFIN47448NominalTestMaximum Dynamic ImpedanceMaximum ReverseZenerCurrentLeakage CurrentVoltage)Vz @ IzTIZTZT @ IzT ZZK @ IzKIZKIRTestVoltage VRVmAΩΩmAµAV1517147000.2511.4llle

Answered: Image /qna-images/answer/b343e6f2-86e1-41dd-8457-f856f3ef4c47.jpg

In the circuit below, when a 2.2KN load is connected to the output, find the value of the current flowing through the R resistor (IR), the current passing through the zener diode (Iz) and the load current value (IL). Sigorta Dr-De 1N4001 T1 0,1A REGOLATOR 220V AC Va-20V Va AC 220 De Vi-15V 15V 4700uF IN4744A Nominal Test Maximum Dynamic Impedance Maximum Reverse Zener Current Leakage Current Voltage1) Vz @ IzT IZT ZT @ IZT ZZK @ IzK IZK IR Test Voltage VR V mA Ω Ω HA V ellle

In the circuit below, when a 2.2KN load is connected to the output, find the value of the current flowing through the R resistor (IR), the current passing through the zener diode (Iz) and the load current value (IL). Sigorta Dr-De 1N4001 T1 0,1A REGOLATOR 220V AC Va-20V Va AC 220 De Vi-15V 15V 4700uF IN4744A Nominal Test Maximum Dynamic Impedance Maximum Reverse Zener Current Leakage Current Voltage1) Vz @ IzT IZT ZT @ IZT ZZK @ IzK IZK IR Test Voltage VR V mA Ω Ω HA V ellle

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1) When is the diode conducting? 2) The maximum current through the load resistor RL is : 3) The maximum reverse voltage across the diode is :
The reverse recovery time of a diode is 8μs and rate of fall of diode current trr di dt = = 10 A/μs, then charge stored during reverse recovery time is A 240μC B 320μC c640μC D 340μC
5. Determine the minimum input voltage required to turn on the Zener diode in the following circuit. Rs=1k LED VD=1.9V RL=2.2k Zener Vz=3.3V
A 500 ohm resistor is connected to a 12V source at one terminal and a 10V zener diode of 250 mW and a 5K ohm resistor are connected to the other terminal. What is the maximum current of the zener diode?
What PIV rating must a diode have to be used in a rectifier with a peak output voltage of 50 V
The input voltage VI is a sinusoidal voltage with maximum value of 4V. If the threshold voltage of the diodes is 0.1 V, plot Vo versus Vı.
For each circuit, use the diode approximation with the forward drop equal to 0.7 V and determine Vout. +3 V 10 k - Vout -3 V ++3 V 10 k - Vout -3 V ++3 V 10 k 5 k -3 V Vout
A silicon diode is in parallel with a germanium diode and is connected to a load resistor having a value of 20 k2 and a forward supply voltage of 10 V. What is the approximate voltage across the silicon diode? * 0.7 V 0.3 V 10 V O 1.0 V
What the range of values of Vi that will maintain the Zener diode in the "on" state. IR R " 220 Ω V₁ R, 21.2 ΚΩ V V/₂= 20 V 12M=60 mA 32.68v to 33.87v 23.67v to 36.37v 20.80v to 38.9v 27.00v to 56.8v
5. Assume each diode in the circuit has a cut in voltage of 0.65V. The input voltage is Vi = 5V. Determine the value of R1 required such that ID1 is one half of ID2. What are the values of ID1 and ID2? R1 VD VD1 Vo VD2 V1 5V R2 1kQ ID1 ID2 3. (a die