A vertical 150-mm-diameter pipe leaves a water tank that has a surface elevation of 12m. Between the tank surface and Elevation 0, 3.3 m of head are lost when 0.06 m³/s flows through the pipe. If an open piezometer tube is attached to the pipe at Elevation 0, what will be the elevation of the water surface (in m) Elev 12m Elev ?4 Elev 0 in this tube? not open to atm

A vertical 150-mm-diameter pipe leaves a water tank that has a surface elevation of 12m. Between the tank surface and Elevation 0, 3.3 m of head are lost when 0.06 m³/s flows through the pipe. If an open piezometer tube is attached to the pipe at Elevation 0, what will be the elevation of the water surface (in m) Elev 12m Elev ?4 Elev 0 in this tube? not open to atm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An open, clean glass tube is inserted vertically into a pan of water. What tube diameter is needed if the water level in the tube is to rise one tube diameter (due to surface tension)? The contact angle is 0 and ss = 0.073 N/m
Suppose a Venturi tube (placed in the horizontal position of Pipe BC in Figure 1) from the right (Fig.2). The radius of the wide part of the tube is 5.0 cm; the radius of the thin part of the tube is 2.5 cm. The tube of shape U is filled with the mercury of the density 13600 kg/m . Determine what heightdifference will be stabilized between the surfaces of the mercury in U-tube. Ignore the losses.
HYDRAULICS LABORATORY EXPERIMENT NO.4 3. Using the value of Cd, which you have obtained by experiment, determine the throat diameter of a Venturi meter which would measure a flow of 0.40 m3/s in a pipe of 0.60 meter diameter with a differential head of 0.80 meter
4. The siphon shown is 76 mm in diameter. It draws oil from a large tank. The loss of head up to the summit is 6 cm and from the summit to the exit is 23 cm of oil. a. Calculate the exit velocity. b. Calculate the pressure at the summit. 0.6 8.3 76- mm 0 siphon
A cylindrical tank of water is 20 m in diameter and 3.5 m tall. There is a 1.0 cm diameter hole at the bottom from which water is leaking. A feeder pipe at the top of the tank, 4.0 m above the ground delivers water at a rate of 0.02 m/min. Ir the tank is initially half full, tal what is the water flow rate in m^3/sec from the top feeder pipe? (bi what is the pressure at the bottom of the tank? (Hint: Bernoul's principle) () what is the water speed at the bottom? (d) what is the leaking flow rate at the bottom? fe) at what rate is the volume of water changing? (Assume the tank is open to air at the top)
1- Water flows through a horizontal pipe at a rate of 9.1 L/s. The pipe consists of two sections of diameters 10.16 cm and 5.08 cm with a smooth reducing section. The pressure difference between the two pipe sections is measured by a mercury manometer. Neglecting frictional effects, (a) determine the differential height of mercury between the two pipe sections. (b) How would the reading change if the manometer on the 2in pipe is replaced by a pitot tube? 10.16 5.08 h
Consider the tank shown in (Eigure 1). Take po = 900 kg/m³, Pu=1000 kg/m³, and pHg = 13 550 kg/m³. 0.6 m 0.8 m 100 mm h 1 of 1 > P Part A Determine the level of water in the tube if the depths of ol and water in the tank are 0.6 m and 0.8 m. respectively, and the height of mercury in the tube is h=0.075 m A Express your answer to three significant figures and include the appropriate units. PA h = 240 Submit + Provide Feedback → OF ? mm Previous Answers Request Answen X Incorrect; Try Again; 4 attempts remaining Next > 1231 AM 0
Weter flows up a tapered pipe (figure). A differential mercury manometer is attached to the pipe at Wand B. The pipe has a diameter of 200 mm at A and 100 mm at B, the point B being 1 m above the alot A. Obtain the deflection in the manometer corresponding to a discharge of 50 L/s. Neglect the friction in the pipe. Relative density of mercury 13.6. %D 100 mm 1 m 200 mm
Q4: A tank of water empties by gravity through a horizontal pipe into another tank in figure (1) .There is a sudden enlargement in the pipe as shown.At a certain time the difference in levels is 3m.Each pipe is 5m long and has a friction coefficient Cf-0.007 The inlet loss constant is K=0.5 and bore diameter in point A 20mm ,and bore diameter in point B 60mm.Calculate this point. the volume flow rate at Calculate the volume flow rate at this point. (1) 20 mm bore diameter 3 m 60 mm bore diameter (2)
An oil flow rate of 0.012 m³/s is required in an industrial process. The flow system includes a pressure tank pushing the oil through 200 m of new ductile iron pipe (DIP: 15 cm diameter, square-edged entrance) to point "2" (atmospheric pressure) as shown in Figure P3.11.11. The sur face of the fluid in the tank (point "1") is at elevation 100 m and the end of the pipe (point "2") is at elevation 106 m. What air pressure will be needed over the fluid to produce the requisite flow? (S.G. (oil) = 0.84, v 2.03 x 106 m²/s, and e = 0.00012 m.)
Water with kinematic viscosity equal to 1.02x10^-6 m^2/s flows in a 1000m long. 150mm diameter pipe (E=0.00005) at a rate of 30L/s. solve for the head loss in the pipe. use 3 decimal places.
An open circular vessel is 1m in diameter and 2m height. It contains water filled to a depth of 1.5m. If the cylinder rotates about its vertical axis, what is the pressure intensity at the center of the bottom if w = 6 radians/second? Unit of the Correct Answer: kPa O 15.542 21.456 16.425 12.465