The figure shown below is a siphon discharging oil (s=0.9). The siphon is composed of 8 cm pipe from A to B followed by 10 cm pipe from B to C. The head losses are: 1 to 2 = 0.3 m 2 to 3 = 0.2 m 3 to 4 = 1 m Compute the discharge in Lit/s and determine the pressures at points 2 to 3 in kPa. 8 cm 10 cm Elev. 5 m в Elev. 3 m A Elev. o DATUM

The figure shown below is a siphon discharging oil (s=0.9). The siphon is composed of 8 cm pipe from A to B followed by 10 cm pipe from B to C. The head losses are: 1 to 2 = 0.3 m 2 to 3 = 0.2 m 3 to 4 = 1 m Compute the discharge in Lit/s and determine the pressures at points 2 to 3 in kPa. 8 cm 10 cm Elev. 5 m в Elev. 3 m A Elev. o DATUM

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The figure shows a siphon discharging oil (s=0.90). The siphon is composed of 8 cm pipe from A to B followed by 10 cm pipe from B to C. The head losses are: Point 1-2: 0.30 J/N Point 2-3: 0.20 J/N Point 3-4: 1.00 J/N Compute the discharge. Determine the pressure at points 2 and 3. 8 cm ø HEL. 5 m HEL. 3 m H10 em g EL. O DATUM
Give me right solution urgent please
a=4 b=0 C=1
Both questions please.
Oil with sp. gr. of 0.87 is being pumped from a lower reservoir to an elevated tank as shown. The pump in the system is 78% efficient and is rated 185 kW. Determine the flow rate of the oil in the pipe if the total head loss from point 1 to point 2 is 12 m of oil. 160mm 200mm s EL 200m El.150m Oil. Sp.gr.=0.82
1. A 0.60 m diameter pipe 600 m long has a head loss of 1.2 m. Find the discharge flowing in the pipe using n=0.014
Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300 m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam E
Oil with sp. gr. of 0.87 is being pumped from a lower reservoir to an elevated tank as shown. The pump in the system is 78% efficient and is rated 185 kW. Determine the flow rate of the oil in the pipe if the total head loss from point 1 to point 2 is 12 m of oil. 160mm 200mm EL.200m W.S. El. 150m Oil. Sp.gr.=0.82
Ex. For the square loop shown: 1. find the discharge in all the pipes. All pipes are 1 km long and 300 mm in diameter, with a friction factor of 0.0163. Assume that minor losses can be neglected. 2. If the required pressure at point d=25 m, then find the required pressure in point A 20 4/5 100 4/6 D 40 L/s C 40 L/S
Kerosene (SG= 0.80 and ? = 68°?) flows from the tank shown and through the 1/4-in.-diameter (ID) tube. Determine the mean velocity in the tube and the discharge. Assume that the only head loss is in the tube.
2. Oil of specific gravity of 0.90 is discharging through a 100 mm circular sharp edge orifice in the end of a 120mm pipe. The pressure head on the center line of the pipe just upstream from the orifice is 9m of oil, and discharges takes place into a closed tank in which the vapor pressure is - 20 kPa. Use C = 0.68 and Cv = 0.97. Compute the discharge. 120 mm pipe P = - 20 kPa 100 mm orifice
Question 2: An 8 in diameter (f=0.028) 500 ft long discharge a 3 in diameter water jet into the atmosphere at a point which is 250 ft below the water surface at intake (Figure 2). The entrance to the pipe is reentrant with ke=0.9 and the nozzle loss coefficient kn=0.045. Find the flow rate and pressure head at the base of the nozzle. D, L, f B kn T D₁ -V₁