A uniform rod has a mass of 2.53 kg and has a length of 1.17 m. It is hinged to a wall by a pivot at one end and is held in a horizontal position by a light vertical string attached to the other end as shown. wall string pivot rod (a) Calculate the magnitude of the tension in the string. (b) The string is now cut. Ignore the mass of the string. Calculate the magnitude of the angular acceleration (in rad/s²) of the rod about the pivot point just after the string is cut. rad/s2

A uniform rod has a mass of 2.53 kg and has a length of 1.17 m. It is hinged to a wall by a pivot at one end and is held in a horizontal position by a light vertical string attached to the other end as shown. wall string pivot rod (a) Calculate the magnitude of the tension in the string. (b) The string is now cut. Ignore the mass of the string. Calculate the magnitude of the angular acceleration (in rad/s²) of the rod about the pivot point just after the string is cut. rad/s2

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A) A woman opens a 1.45 m wide door by pushing on it with a force of 42.5 N applied at the center of the door, at an angle perpendicular to the door's surface. What magnitude of torque (in N · m)is applied about an axis through the hinges? __________N · m B) A second person opens the same door, using the same force, again directed perpendicular to the surface, but now the force is applied at the edge of the door. What magnitude of torque (in N · m) is applied about the axis through the hinges now? _________N · m
A uniform 8.00 m, 1500 kg beam is hinged to a wall and supported by a thin cable attached 2.00 m from the free end of the beam, as shown in the figure. The beam is fixed to the wall by a hinge at an angle of 30.0 degrees above the horizontal. The angle between the cable and the beam is 40.0 what is the direction of torque exerted by the beam around the point where the cable is attached to the beam? a) clockwise b) counterclockwise
Needs Complete typed solution with 100 % accuracy.
A metal rod 6.00 m long is held in a horizontal position. An object with mass 3.70 kg is suspended from a light rope that is attached 4.00 m from the left-hand end of the rod, as shown in the figure below. Take counterclockwise torques to be positive. For an axis at the right-hand end of the rod, what is the torque exerted on the rod by the tension in the rope? 6.00 m |axis 4.00 m
The slender rods presented in the structure have a mass of 6.5 kg/m. You are required to: a) Determine the centre of mass for the structure. b) Determine the moment of inertia for the structure about an axis perpendicular to the page at the centre of mass. CONNECTION 75 mm STANCHION- I 75 mm A LONGITUDINAL "A STRAKE 160 mm
A 3.00-kg stone is tied to a thin, light wire wrapped around the outer edge of the uniform 8.00-kg cylindrical pulley. The inner diameter of the pulley is 55.0 cm, while the outer diameter is 1.00 m. The system is released from rest, and there is no friction at the axle of the pulley. a) Find the acceleration of the stone and the tension of the wire. b) Find the angular acceleration of the pulley.
You push on the door as shown in the drawing. Calculate the torque experienced at the door hinge.
A bar 1m in length has a negligible mass and it is placed on a pivot point at the 0.55 m mark. A 2.3 kg mass hung at the 0 m mark and a 1.5 kg mass hung at the 1.0 m mark. The meterstick is released from rest in a horizontal position. Immediately after release, the magnitude of the SUMMATION OF TORQUE on the bar about the pivot point is most nearly A) 8.0 N•m B 2.0 N-m c) 6 N•m D 16 N•m E) 19 N•m
A constant horizontal force of 10 N is applied to a wheel of mass = 10 kg and radius of 0.3 m. The center of mass of the wheel has an acceleration of 0.48 m/s/s. a) Determine the magnitude of the friction force acting on the wheel. b) Determine the magnitude of the rotational inertia if the linear acceleration were 0.48 m/s/s. You will have to recalculate the friction force.
Consider an unsuccessful attempt to take off a tire using a wrench to loosen the bolts. Assume the wrench is 0.3m long and are you able to apply a 200N force Because the tire is flat you can only apply your force at a 60° angle. What is the torque at the center of the bolt. You find a tire jack and are now able to apply 200N of force at an 80° angle. Is the resulting torque more or less and what is the new torque.
A fixed crane has a mass of 361.4kg and is used to lift a 217.6kg crate. It is held in place by a pin at A and a rocker at B as shown in the figure below. The center of gravity of the crane is located at G. What must be the value of the net torque at point A if the crane is in equilibrium? (Include the Sl unit in your answer.) A 1.5 m |B -2 m 4 m
Which of the following statement is false? Unit of Torque is Newton Meter. An object is said to be in equilibrium if and only if there is no resultant force and no resultant torque. An object is said to be in equilibrium if and only if there is no resultant force and no resultant torque. Angular acceleration of object is zero if it is not rotating or rotating with constant angular velocity. None of the above.